Cadet NLW Serie Guia Del Propietario página 3

Installation Instructions
How do I insert the heater
assembly into the wall can?
Assembly
STEP 1
Place heater assembly inside wall can
and secure with two screws (provided).
STEP 2 Wire
Connect the 2 heater wires to the 2
supply wires using electrical insulated
wire connectors. Push wires into
wiring junction box.
STEP 3 Grill
Secure grill with screws provided and
attach thermostat knob.
Important: Before turning on power, be
sure the thermostat knob is turned counter
clockwise to the lowest setting, and the
switch is in the "FAN" or "AUTO" position.
Operation & Maintenance
How to operate your heater
Fan cycling with heat
1. Turn fan switch to the "auto" position and turn
the thermostat knob fully clockwise.
2. When the room reaches your comfort level,
turn the thermostat knob counterclockwise
until the heater turns off. The heat and the
fan will automatically cycle around this
preset temperature.
3. To reduce the room temperature, turn the knob
counterclockwise. To increase the room
temperature, turn the knob clockwise.
Fan running continuously with intermittent heat
(Determined by thermostat setting)
1. Turn the fan switch to the "FAN" position and
turn the thermostat knob fully clockwise.
2. When the room reaches your comfort level, turn
the thermostat knob counterclockwise until the
heater turns off. The heater will automatically
cycle around this preset temperature, however
the fan will run constantly.
3. To reduce the room temperature, turn the knob
counterclockwise. To increase the room
temperature, turn the knob clockwise.
Fan running continuously with no heat
1. Turn the fan switch to the "FAN" position.
2. Turn the thermostat knob just above the
"OFF" position.
Maintenance
As needed, or every six months minimum.
1. WARNING! Before removing grill, turn the
electrical power off at the electrical panel
board (circuit breaker or fuse box). Lock or tag
the panel board door to prevent someone from
accidentally turning the power on while you
are working on the heater. Failure to do so
could result in serious electrical shock, burns,
or possible death.
Part Two
t
e n
j a c
c e
A d
r f a
S u
THERMOSTAT
4 6
1 3
THERMAL
LIMIT
WIRING DIAGRAM
2. It is important that you verify power has been
turned off and no power is going to the heater
before proceeding. Circuit breakers are often not
marked correctly and turning the wrong breaker
off could mean electricity is flowing to the heater,
even if the heater does not appear to be working.
If you are uncomfortable working with electrical
appliances, unable to follow these guidelines,
or do not have the necessary equipment, consult
a qualified electrician.
3. Once you verify the power has been turned off
correctly, proceed to the next step.
4. Remove screws and take off grill.
5. Wash grill with hot soapy water and dry
immediately.
6. While holding fan (to avoid damage or bending),
use a hair dryer or vacuum on blow cycle to blow
debris through the element (Do not touch element).
7. Vacuum fan area without touching the elements.
8. Replace grill and secure with screws.
9. Turn thermostat to desired setting.
10.Turn power back on at the electrical panel board.
About the Heater Temperature-Limiting Controls
The heater is protected by a high temperature manual
reset limiting control, designed to open the heater
circuit when excessive operating temperatures are
detected. The problem must be assessed and the
limit must be reset to resume operation.
Resetting the Manual-Reset Limit Control
If the manual reset limit control has opened the
heater circuit due to excessive operating
temperatures, the heater will not work until the limit
reset button is pressed. After allowing the unit to
cool for at least 10 minutes, turn the electrical
power off at the electrical panel board (circuit
breaker or fuse box) and remove the grill. Once the
problem causing the limit to trip has been resolved
(typically heater is blocked or needs cleaning), push
button located on the left side of the heat box. Press
FIRMLY, and be sure to listen and feel for a click,
indicating it has been reset.
FIGURE 5
FAN
SWITCH
MOTOR
ELEMENT
WARNING
Risk of Electrical
Shock. Connect
grounding lead
to grounding wire,
or screw provided.
Keep all foreign
objects out of
heater.
WARNING
Risk of Fire.
Heater must be
kept clear of all
obstructions: a
minimum of 3 feet
in front; 6 inches on
both sides and
above. Heaters
must be kept clean
of lint, dirt and
debris.
WARNING
Turn the electrical
power off at the
electrical panel
board (circuit
breaker or fuse
box) and lock or
tag the panel board
door to prevent
someone from turn-
ing on power while
you are working on
the heater. Failure
to do so could
result in serious
electrical shock,
burns, or possible
death.
3