Publicidad
FEATURES
PRESSURE
MODEL
INT.
DIAM.
HOSE
(in)
Low
23RW350
3/8"
Low
23RW450
1/2"
Medium
23RO250
1/4"
Medium
23RO350
3/8"
Medium
23RO450
1/2"
High
23RG250
1/4"
High
23RG350
3/8"
CAUTIONS
For use only in applications for which that tool were designed
which it was not intended
Stay alert.
Watch what you are doing, use common sense. Do not operate any tool when you are tired
Check for damaged parts.
Before using any tool, any part that appears damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment and binding of moving parts any broken parts or mounting
fixtures and any part that is damaged should be properly repaired or replaced by a qualified technician.
Replace parts and accessories.
any parts will void the warranty.
Do not operate tool under the influence of alcohol or drugs.
reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool.
Maintenance.
For you safety, maintenance should be performed regularly by a qualified technician.
WARNING:
The warnings, cautions and instruction discussed in this instruction manual cannot cover all possible conditions and
situations that may occur. It most be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
OPERATION
(See figure 1)
Adjusting tension on spring.
1. Pull out six feet of hose out of reel.
2. Remove the hose stopper from the hose and feed it back trough the guide.
3. To increase tension, wrap the hose one time from the drum.
4. To decrease tension, unwrap the hose one time from the drum.
5. Run back the hose through the guide and re-attach the hose stopper.
6. Unlatch the hose and check the tension. Adjust the stopper position or spring stopper if is necessary.
REPLACEMENT OF HOSE
1. Pull out the old hose and lock the reel.
2. Disassemble the Rubber Bumper Block (#63) by removing the Bolts (#61) and the Nuts (#64).
3. Disconnect the old hose from the swivel joint and remove the hose.
4. Run the hose (#2) through the Rubber Bumper Block (#63) and through the opening in the drum flange.
5. Use Teflon tape on the hose fitting treads and screw the fitting onto the swivel and tighten. Reassemble the Rubber Bumper Block
(#63) with the Bolts (#61) and the Nut (#64)
6. Attach the hose stopper on the end of the hose near the outlet fitting.
7. Carefully release drum latch and allow the hose (#2) to wind onto the reel.
Try to evenly distribute the hose (#2) across the reel.
NOTE:
Some parts are listed and show for illustration purpose only and are not available individually as replacement parts.
LENGTH
PRESSURE
OUTLET
HOSE
MAX
HOSE
MALE
(feets)
(m)
(PSI)
(BAR)
(NPT)
50ʼ
15.2
300
20
3/8
50ʼ
15.2
300
20
1/2
50ʼ
15.2
2750
190
1/4
50ʼ
15.2
2250
155
3/8
50ʼ
15.2
2000
138
1/2
50ʼ
15.2
5000
345
1/4
50ʼ
15.2
4000
276
3/8
When use a service, use only identical parts only use accessories intended for use with this tool. Use of
E N G L I S H •
IN HOSE
DIMENSION
MALE
ØW
(NPT)
(in)
(cm)
(in)
1/2
17.5
44.5
7.375
1/2
17.5
44.5
7.375
3/8
17.5
44.5
7.375
1/2
17.5
44.5
7.375
1/2
17.5
44.5
7.375
3/8
17.5
44.5
7.375
1/2
17.5
44.5
7.375
. Do not modify this tool and do not use this tool for a purpose for
Read warning labels on prescription to determine if your judgment or
U ser's manual
WEIGHT
IDTH
HEIGHT
(cm)
(in)
(cm)
(pounds)
18.733
21
53.3
39.65
18.733
21
53.3
50.66
18.733
21
53.3
35.24
18.733
21
53.3
39.65
18.733
21
53.3
50.66
18.733
21
53.3
35.24
18.733
21
53.3
39.65
(kg)
17.985
22.979
15.985
17.985
22.979
15.985
17.985
4
Publicidad
