ELCART 12/23060 Guia De Inicio Rapido página 2

PROJECTOR SUSPENSION SUPPORT INSTRUCTION
ART. 12/23060 Silver color
1. Technical parameter:
Weight:
Maximum load:
Tilt from ceiling:
2. Part list:
Please check the parts in the package compare with the following list.
Make sure all of the parts are in the package.
Never use defective parts.
Never replace part with different specification.
Note: Incorrect installation may cause injury!
No. Name of Part Material
Amount
A M8*60 Metal anchor Standard part
B Plastic washer PA
C Ø3 flat washer Standard part
D Ø4 flat washer Standard part
E Ø5 flat washer Standard part
F M3*10 screw Standard part
G M4*10 screw Standard part
H M5*10 screw Standard part
I Inner hexagon spanner S=6 Standard part
J Spanner S=13 Standard part
K Short mounting plate Standard part
Supporting component Assembled part
-
- Connection component Assembled part
3. Installation and operation instructions
Note: please read the instructions carefully before installation!
Step 1:
Use the fixing component as a templet to drill 4 holes of Ф10mm and 50mm deep on the ceiling.
The holes should be symmetrical and balanceable in horizontal and vertical direction. Insert four metal anchors
into these holes, then tighten the fixing component. Remove the flat washers, spring washers and nuts from the
steel anchors, then place Fixing component on the four screws exserted, and then install the flat washers,
spring washers and nuts on the four screws.
Each nut should be screwed down to make the steel anchor and Fixing component and the ceiling be fastened.
ELCART DISTRIBUTION SPA via Michelangelo Buonarroti, 46 - 20093 Cologno Monzese (Milano) ITALY
Tel. ++39(0)2/25.11.73.10 Fax ++39(0)2/25.11.76.10 sito internet: www.elcart.com
La divulgazione dei dati contenuti in questa scheda è da ritenersi un servizio puramente informativo e non costituisce alcun vincolo da parte della Elcart in merito a prestazioni ed utilizzo del prodotto.
2,4 kg. Pitch angle of projector:
20 kg. Rotation:
0°÷90° Distance from ceiling:
4
1
4
4
4
4
4
4
1
1
4
1
1
Step 2:
When mounting the connection components, the four Z-formed
connecting patches should be laid reasonably according to
the position of the holes in the upper part of the projector.
And the screws should be selected according to the size of
±30°
the thread holes in the projector.
360°
Please place the projector as center as possible,
470÷670 mm
then screw all the bolts.
Step 3:
When mounting the projector, unscrew the knobs in two sides of the projector at first, and don't let the
knob end over the inner surface to avoid failing to mount.
And then put the plastic washer into the connection component.
The purpose of mounting as the shape is to preventing internal abrasions.
(Don't loose the two side knobs at the same time for fear that it drops).
Step 4:
After the installation has been completed, you may adjust the angle and the flex
the distance of the project as your need.
Note: this product can be installed on the slantwise wall.
Adjust the position of projector to a suitable place
according to the different tilting angle.
4. Notes
(1) Choose the right place to install projector mount.
The mount must be installed on solid concrete ceiling.
Make sure the ceiling can support 80kg weights up.
(2) If you are unsure of any part of the installation process, contact a professional installer for assistance.
(3) A minimum of two adults are required for this installation.
(4) This product is intended for indoor and personal use only.
MADE IN CHINA
IMPORTED AND DISTRIBUTED BY:
ELCART DISTRIBUTION SpA
VIA MICHELANGELO BUONARROTI, 46
20093 COLOGNO MONZESE (MI)
ITALY
www.elcart.com - info@elcart.it
e-mail: info@elcart.it