Kohler STERLING 5406 Serie Instrucciones De Instalación Y Cuidado

Sliding Bath Doors Sliding Shower Doors
USA/Canada: 1-800-STERLING (1-800-783-7546)
México: 001-877-680-1310 SterlingPlumbing.com
Critical Information!
Read Before Installation!
WARNING: Risk of serious injury. Damage prior to installation can
result in glass shattering. Inspect the glass and all parts for damage
before installation.
WARNING: Risk of serious injury. Improper installation can result
in glass shattering. Follow all installation instructions.
WARNING: Risk of serious injury. Do not cut tempered glass.
Tempered glass will shatter if cut.
WARNING: Risk of serious injury. Shower door and side panels
can shatter. Regularly inspect the glass and all parts for damage,
missing, or loose parts.
WARNING: Risk of serious injury. Always wear safety glasses
while cutting and drilling.
IMPORTANT! Do not touch the edges of the tempered glass with tools or
any other hard objects. Do not set the unframed tempered glass directly on
the floor or any hard surface.
IMPORTANT! Leave this manual for the end user.
Read these instructions before installing or using this product.
IMPORTANT! Do not cut the top track the same length as the bottom track.
NOTICE: The warranty does not apply to a product that has been modified
or altered in a manner other than as expressly permitted in the Installation
and Care Guide.
Walls must be within 3/8" (10 mm) of plumb.
Cover the drain with tape to avoid loss of small parts.
Follow the silicone sealant manufacturer's instructions for application and
curing time.
To watch this installation online, visit the product page at
www.sterlingplumbing.com.
For care and cleaning and other information; visit
www.sterlingplumbing.com/care-and-cleaning.
Read and follow all instructions.
Slide the notched end of the insert into the
1
groove and pull the notch to the end of the
bottom track. Trim the insert to be flush with the
bottom track.
Insert
Notch
Bottom Track
Position the wall jambs over the bottom track.
6
Plumb both wall jambs. Mark the screw holes.
x2
1204886-2-D
Required Tools
Number 2 Pencil
Tin Snips
100% Silicone Sealant
Masking Tape
Miter Box
32 Teeth Per Inch Blade
Center Punch
3/16" 5/16"
5/16" Masonry Bit for Tile
Measure distance "A." Subtract 1/4" (6 mm) or
2
the width of a number 2 pencil from "A" and cut
the bottom track.
A
1/4" (6 mm)
"A" Mark
Cut Line
A
Remove the wall jambs. Drill 5/16" holes into the
7
walls and insert the anchors.
x2
3
2
1
Parts Identifi cation
1203633
Hardware Skin Pack
1205305**
Hanger Bracket Kit
Series Number Label
#8-32 x 3/8"
1199426-01**
Hanger Bracket
1199110
Gasket
1050048-B
Barrel Nut
Wall Jamb*
8-32 x 1/4"
1184244
Cover (4 ea.)
1172113
Towel Bar
Bracket Kit
(4 ea.)
#8-18 x 1-1/2"
1048208-C
Screw
Bottom Wall
Jamb Notch
Postition the bottom track on the center of the
3
ledge. If needed, file the ends to match the
corners.
Apply silicone sealant in the groove on the
8
underside of the bottom track. Secure the bottom
track to the ledge along the marked location.
Groove
1
Installation and Care Instructions
*Need help? Contact the STERLING Customer Care Center
1183518-01**
Top Track
1051142-A
1044585
Screw
Roller
1077763-A
Bolt
Door Panel*
1161993-01** [23" (584 mm)]
1161993-02** [19" (483 mm)]
Towel Bar (2 ea.)
1056868-A
Screw
1053530
Insert
1058294**
Center Guide
Center the bottom track on the ledge with the leg
4
to the outside. Tape the bottom track in place and
mark the position.
Leg
Reposition both wall jambs. Secure the wall
9
jambs with screws. Attach a bumper at the top
and bottom locations.
x2
Screw Cover
#8-18 x 1-1/2"
Screw Cover
5406 Series Sliding Shower and Bath Doors
at 1-800-STERLING (1-800-783-7546).
For service parts information, care and cleaning, and
other information, visit www.sterlingplumbing.com
**Finish/color code must be specifi ed when ordering.
Retain this document for future servicing.
Record model number from box for reference.
Model Number:______________
1081001
Bumper
Wall Jamb*
1031943**
Screw Cover
1077762
Anchor
Bottom Wall
Jamb Notch
1058626-02**
Bottom Track
IMPORTANT! The bottom track and wall jamb
5
must sit flat against the shower ledge and the
wall. If needed, trim and file the wall jamb. Use a
coin to match and to transfer the corner radius of
the shower to the wall jamb.
Notch
Check the bumpers for the correct horizontal
10
alignment with the wall jambs.
Correct Incorrect