Atlas Lighting Products WL Serie Instrucciones De Instalación

Lighting Products Lighting Products
Atlas Atlas
Lighting Products Lighting Products
Atlas Atlas
Models: WL, WLG Series
IMPORTANT: READ BEFORE REMOVING FIXTURE FROM CARTON.
Lighting Products Lighting Products
RETAIN FOR FUTURE REFERENCE
Atlas Atlas
SAFETY: This fixture must be wired in accordance with the NATIONAL
ELECTRICAL CODE and applicable local codes and ordinances. A person
familiar with the constructionand operation of the product and the hazards
Lighting Products Lighting Products
involved must install this product. A qualified licensed electrician should
complete all work. Proper grounding is required for safety.
WARNING: Make certain power is OFF before installing or maintaining fixture.
Atlas Atlas
RISK OF INJURY: Fixture may become damaged and/or unstable if not
installed properly.
Lighting Products Lighting Products
Atlas Atlas
MOUNTING
Fixture must be located at least 18" below any structural detail. Do not
recess fixture.
JUNCTION BOX MOUNTING
(Mount to weatherproof junction box using 1/2" conduit nipple.)
Lighting Products Lighting Products
1. Open front housing by removing screws.
Atlas Atlas
2. Remove reflector by removing screws.
3. Remove knockout plug on the back of the fixture.
4. Pull supply wires through mounting plate and attach to mounting box.
5. Seal with weatherproof silicone sealant to prevent moisture from
entering the fixture.
Lighting Products Lighting Products
6. Replace reflector, install lamp and replace front housing.
CONDUIT MOUNTING
1. Remove front housing by removing screws.
2. Remove reflector by removing screws.
3. Attach conduit to fixture.
4. Secure fixture to wall using the appropriate hardware.
5. Pull leads into fixture and make connections as noted in the
wiring section.
6. Replace reflector, install lamp and replace front housing.
THREE OR FIVE-YEAR LIMITED WARRANTY: Atlas warrants that its products will be free from failure in materials and workmanship for a period of three (3) years from the date on which the
product was purchased from Atlas. This warranty applies to LED products, motion fixtures, motion sensors, and electronic ballasts for a period of five (5) years. When this three or five-year warranty
period ends, all warranties (whether express or implied) and liability of Atlas shall immediately cease. The warranty period for all lamps and photocells is one (1) year.
LIMITATION ON IMPLIED WARRANTIES: ALL IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR PURPOSE,
ARE LIMITED TO AND SHALL NOT EXCEED THE TERMS OF THIS LIMITED WARRANTY.
FURTHER LIMITATIONS OF THIS WARRANTY: This limited warranty DOES NOT cover damage resulting from accident, misuse, abuse, improper repair, lack of reasonable care, modification
(including but not limited to use of unauthorized parts or attachments), alteration, loss of parts, installation and operation contrary to printed instructions, vandalism, acts of God (lightning, power
surges, water damage or similar failure), or transit (including UPS shipments). This limited warranty also does not include labor costs associated with installing replacement parts for any failed parts
returned to Atlas under this warranty.
DUTY AND PROCEDURE TO NOTIFY ATLAS OF FAILED PRODUCT: Notification of a failed product under this warranty must be provided to Atlas within ninety (90) days after discovery of the
failure. Notification occurs only by sending the following to Atlas: (1) sales receipt, (2) the date of purchase, and (3) a brief explanation of the nature of the failure. This information must be either
e-mailed to Atlas at returns@alpinc.com or mailed to Atlas Lighting Products, Inc., Attn: Returns Department, P.O. Box 2348, Burlington, NC 27215. The date of the postmark of the mailing to Atlas
shall constitute the date of notification under this warranty. If the information is e-mailed, the date that the e-mail is sent to Atlas shall constitute the date of notification under this warranty. Upon
receiving a timely notification, Atlas will, if the notification reflects a failure of materials or workmanship, provide a Return Goods Authorization number and full
instructions for returning failed merchandise. All returned goods must be accompanied by a Return Goods Authorization number issued by Atlas.
SOLE REMEDY: REPAIR OR REPLACEMENT: If, upon receiving a timely notification with the information stated above and receiving merchandise that appears to Atlas to have a failure in
materials or workmanship, Atlas will — at Atlas's sole option — either repair the failed part(s) or provide a replacement part or parts. This remedy constitutes the sole remedy under this warranty and
Atlas's sole liability in connection with any failed part(s). Atlas shall not be liable for any other expense, injury, loss or damage, whether direct, special, incidental, or consequential
(including but not limited to loss of use, income, profit, or production, inconvenience, increased cost of operation, and spoilage of or damage to material and personal property). As
stated above, this limited warranty does not include labor costs associated with installing replacement parts for any failed parts returned to Atlas under this warranty.
NO OTHER REPRESENTATIONS: No other representations, written or verbal, have been authorized by Atlas. No representative of Atlas has any authority to waive, alter, vary, or add to the terms
hereof without prior approval in writing by an authorized representative of Atlas.
SEVERABILITY: The foregoing provisions are severable. If any provision shall be unenforceable for any reason, the other provisions shall remain in effect.
DISCLAIMER: ATLAS LIGHTING PRODUCTS, INC. MAKES NO REPRESENTATIONS (WRITTEN OR VERBAL) OR WARRANTIES (EXPRESS OR IMPLIED) AS TO ANY MATTER
WHATSOEVER, INCLUDING WITHOUT LIMITATION THE CONDITION, MERCHANTABILITY, OR FITNESS FOR ANY PARTICULARY PURPOSE OF ANY PRODUCT, EXCEPT AS EXPRESSLY
SET FORTH UNDER THIS LIMITED WARRANTY.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
11" WALL LIGHTS
INSTALLATION INSTRUCTIONS
WIRING
1. The supply voltage must match the fixture operating voltage.
2. Connect the black fixture lead wire to the black supply wire.
3. Connect the white fixture lead wire to the white supply wire.
4. Connect the supply ground wire to the green screw on the fixture.
5. Insulate the ends of all unused ballast leads.
NOTE: Optional 0-10 V Dimming. Dimming provided through grey & purple wires.
Refer to control manufacturer for wiring instructions.
LAMP SERVICE
Caution: Prior to installing, check that the lamp is of proper type
1. Disconnect power.
2. Make sure fixture and lamp are cool enough to touch.
2. Loosen two screws holding lens.
3. Remove lens.
4. Replace lamp. Make sure lens gasket is properly seated.
5. Close lens and re-install screws.
TROUBLESHOOTING
Check that:
1. Proper lamp is installed.
2. Line voltage at the fixture is proper.
3. Fixture is wired properly.
4. Fixture is grounded properly.
ATLAS LIGHTING PRODUCTS, INC.'S LIMITED WARRANTY
Multi-volt fixtures are prewired at the factory for 277V operation.
If an alternate supply voltage is used, then reconnect the black
fixture lead wire to the appropriate ballast lead (voltages are
marked on ballast lead wires).
Warning: Improper wiring may result in ballast failure which
voids all warranties.
and wattage. Observe lamp manufacturer's recommendations
on lamp operation, ballast type and burning positions.
240-007H