ETI DL-8-30-903-MV-D Guía De Uso Y Cuidado

nOTe: Keep your receipt and these instructions for proof of purchase.
WarninG: Shut off the power at the circuit breaker or fuse panel before removing the old fixture, ballast, or fluorescent
tubes.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.
INSTALLATION
Part # DL-6-80-903-MV-D / Order # 53192211 can be installed into 5 in. and 6 in. housings.
Part # DL-8-30-903-MV-D / Order # 53189111 can be installed into 8 in. and 10 in. housings.
Shut off power at the electrical panel before beginning the installation.
1
Remove existing fixture and set aside to recycle in accordance with local requirements.
2
Choose your favorite correlated color temperature (CCT) before installing the fixture.
3
nOTiCe: The factory setting for the correlated color temperature (CCT) is 3000K, which is the warmest white light.
Electrical
Box
A
Open electrical box cover.
4
Ground
Black
White
Electrical
Source
Purple
Grey
Make the electrical connections:
7
• Black wire to black wire.
• White wire to white wire.
• Ground wire to ground.
• If 0-10v dimming is available:
Connect purple wire to purple wire.
Connect gray wire to gray wire.
• If 0-10v dimming is not available:
Cover wires with wire connectors.
WarninG: Carefully read and understand the information given in this manual before beginning the assembly and installation. Failure to do so could lead to electric shock, fire, or
other injuries which could be hazardous or even fatal. • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
nOTiCe: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which
the receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Use anD Care GUiDe
COLOr PreFerenCe
Knock out
Holes
Punch out 1 of the knock out holes.
5
Fixture
Questions, problems, missing parts? Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com
reCesseD LeD DOWnLiGHT
®
Compress the spring clips and insert the fixture
8
into the opening in the ceiling.
Ordering # 53189111, 53192211
Part # DL-8-30-903-MV-D, DL-6-80-903-MV-D
Certification # 53189111-1, 53192211-1
PAckAgE cONTENTS
Part Description Quantity
A Fixture
Run wires per local electrical code and
6
feed wires through the knock out hole.
1
A