Bayco 821 Guia De Inicio Rapido

Instruction Manual
Model 821
13 Watt Fluorescent Work Light
on Retractable Reel
Electrical Rating - All models use 125 Volts 60 Hz
CAUTION - TO REDUCE THE RISK OF ELECTRIC SHOCK AND FIRE - PULL
PLUG WHEN SERVICING, CONNECTING/DISCONNECTING FROM THE LAMP OR
WHEN RE-LAMPING - USE ONLY 13 WATT OR SMALLER BULB
CAUTION
DO NOT use in explosive atmospheres, near fl ammable liquids, or where explosion
proof lamps are required.
DO NOT use in the proximity of vehicles or equipment when there is a risk of
fl ammable liquids coming into contact with the hand lamp.
DO NOT immerse in water.
DO NOT use in areas where water can accumulate or in rain or mist.
CAUTION: Risk of Electric Shock – For Light Duty Dry Location Use Only.
GENERAL USE CORD REEL ONLY. NOT FOR HARD USE. FOR INDOOR DRY
LOCATION USE ONLY FOR LIGHT DUTY RESIDENTIAL USE ONLY
WARNING: NOT FOR USE ABOVE HAZARDOUS LOCATIONS
CAUTION: DO NOT USE IN HAZARDOUS LOCATIONS AS REQUIRED BY THE
CANADIAN ELECTRICAL CODE, PART I
IMPORTANT SAFETY INSTRUCTIONS
This product has a 3 prong polarized plug on the power cord. Do not attempt to
bypass this safety feature by removing the round plug and defeat his safety feature. This
plug will fi t into a grounded outlet only one way. If the plug does not fi t fully into the outlet,
contact a qualifi ed electrician. Never use with a two wire extension cord.
IMPORTANT NOTICE: THIS PRODUCT IS ETL LISTED
CAUTION: PULL OUT CORD TO FULL LENGTH WHEN USING RECEPTACLE
CAUTION: DO NOT ALLOW THE CORD TO RETRACT BY ITSELF AS DAMAGE
OR INJURY MAY OCCUR FROM EXCESSIVE REWIND SPEED
CAUTION: DRYWALL WILL NOT HOLD THE WEIGHT OF THE REEL ASSEMBLY
CAUTION: READ AND UNDERSTAND MOUNTING INSTRUCTIONS BEFORE
ATTEMPTING INSTALLATION AND USE OF THIS PRODUCT
OPERATION
• Plug into 120 Volt 60 Hz polarized outlet. Notice the polarized plug and insert
properly. Operate switch. Lamp may fl ash several times before lighting.
• Some models have a 3-wire grounded outlet as a power source for electrical tools
or other appliances not exceeding 6.4 AMPS. The outlet will also accept a two-wire
polarized plug.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.mybayco.com
• Pull out desired length of cord. Notice a clicking noise when pulling. Cord will stay
at the desired length during clicking and rewind after a pull past the clicking noise.
Extended length when retracted can be adjusted by sliding plastic ball to desired
position.
CAUTION: PULL OUT CORD TO FULL LENGTH WHEN USING RECEPTACLE
CAUTION: DO NOT ALLOW CORD TO RETRACT BY ITSELF, AS DAMAGE TO
CORD END FITTINGS MAY OCCUR FROM EXCESSIVE REWIND SPEED.
BULB REPLACEMENT
1. Disconnect the unit from electrical outlet
2. Remove the lens and & cover screws located on each side at the top end of lamp.
3. Pull the lens out and up to expose the bulbs
4. Slide the bulb holder cushion from around the top of the bulb. The bulb will remain
in the socket
5. Grasping the bulb at the top, pull forward and carefully pull up on the bulb to remove.
6. Insert the new bulb in the socket and bulb holder. Be sure the bulb is properly seated
against the bulb holder
7. Slide the bulb holder cushion back into place on the top of the bulb and align the
screw holes with the holes on the side of the light
8. Push the lens back into place on the front of the light and snap into place
9. Align the holes in the lens with the holes in the side of the light and replace the screws.
10. Restore power connection and test lamp by pressing the power switch.
NOTE: Even new lamps will fl ash several times before lighting.
REPLACEMENT BULBS
Use PL-13 twin-tube fl uorescent bulb.
A replacement lamp may be obtained from Bayco products.
MOUNTING
Ceiling or Wall Installation
11. Select a location within 18 inches of an electrical outlet. The outlet for a garage door
opener is desirable.
12. Drywall will not hold the weight of the reel assembly, so locate a ceiling joist or wall
stud and using the mounting bracket as a template, mark the holes so they are centered
on the ceiling joist or stud.
13. Attach the mounting bracket to the stud using the 2 wood screws provided.
14. Align the holes on the side of the reel with the holes in the side of the mounting
bracket and insert the pin.
15. Place the retaining ring on the pin and twist until the entire ring is through the hole
in the pin. DO NOT operate this reel without the retaining ring in place on the pin.
SAFETY/CARE
• Caution: do not allow the cord to retract by it self as damage or injury may occur from
excessive rewind speed.
• Adjust the cord stop to hold the receptacle at the desired length when the cord is
retracted.
• Before cleaning the reel always unplug from the power source.
INS-821-19