Ryobi Tek4 RP4000 Manual Del Operador

OPERATOR'S MANUAL
Tek4 Lithium-ion
®
Self-leveling
Plumb/Cross Laser
RP4000
IMPORTANT SAFETY
INSTRUCTIONS
WARNING:
READ AND UNDERSTAND ALL INSTRUCTIONS. Failure to
follow all instructions listed below, may result in electric shock,
fire and/or serious personal injury.
CAUTION:
Use of controls or adjustments or perfor mance of pro-
cedures other than those specified herein may result in
hazardous radiation exposure.
 The laser guide radiation used in the plumb/cross laser
attachment is Class IIIa with <5mW and 630-670nm
wavelengths.
 Avoid direct eye exposure when using the laser and do
not project the laser beam directly into the eyes of others.
Serious eye injury could result.
 Do not remove or deface any prod uct labels. Removing
product labels increases the risk of exposure to laser radia-
tion.
 Do not place the instrument in a position that may cause
anyone to stare into the laser beam intentionally or
unintention ally. Serious eye injury could result.
 Do not operate the plumb/cross laser around children or
allow children to operate the tool. Serious eye injury could
result.
 Always turn the plumb/cross laser off when not in use.
Leaving the tool on increases the risk of someone inadver-
tently staring into the laser beam.
 Do not operate the instrument in com bustible areas
such as in the presence of flammable liquids, gasses, or
dust.
 Always ensure the laser beam is aimed at a surface with-
out reflective proper ties. Shiny reflective materials are not
suitable for laser use.
 The laser shall be used and maintained in accordance
with the manufacturer's instructions.
 Never aim the beam at a person or object other than the
target surface.
 This product should not be used without the battery cap
installed.
 Handle the instrument with care. Treat it as you would any
other optical device such as a camera or binoculars.
 Avoid exposing the instrument to shock, continuous vibra-
tion, or extreme hot or cold temperatures. Damage to the
product and/or serious injury to the user could result.
 Use battery only with charger listed.
MODEL BATTERY PACK
RP4000 AP4001
 Do not use on a ladder or unstable support. Stable footing
on a solid surface enables better control of the product in
unexpected situations.
 Do not use the product if the switch does not turn it on
and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
 Use the product in accordance with these instructions
and in the manner intended for the product, taking into
account the working conditions and the work to be
performed. Use of the product for operations different from
those intended could result in a hazardous situation.
 Ensure the switch is in the off position before inserting
battery pack. Inserting the battery pack into products that
have the switch on invites accidents.
 Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another
battery pack.
 Use battery products only with specifically designated
battery packs. Use of any other battery packs may create a
risk of injury and fire.
 When servicing a battery product, use only identical
replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or failure
to follow Maintenance instructions may create a risk of shock
or injury.
 Know your battery product. Read operator's manual
carefully. Learn its applications and limitations, as well as
the specific potential hazards related to this power tool.
Following this rule will reduce the risk of electric shock, fire,
or serious injury.
 Do not place battery products or their batteries near fire
or heat. This will reduce the risk of explosion and possibly
injury.
 Do not crush, drop or damage battery pack. Do not use
a battery pack or charger that has been dropped or
received a sharp blow. A damaged battery is subject to
explosion. Properly dispose of a dropped or damaged battery
immediately.
 Batteries can explode in the presence of a source
of ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush with water
immediately.
 Do not charge battery tool in a damp or wet location.
Following this rule will reduce the risk of electric shock.
 For best results, your battery tool should be charged in
a location where the temperature is more than 50°F but
less than 94°F. To reduce the risk of serious personal injury,
do not store outside or in vehicles.
 Under extreme usage or temperature conditions, battery
leakage may occur. If liquid comes in contact with your
skin, wash immediately with soap and water. If liquid gets
into your eyes, flush them with clean water for at least 10
minutes, then seek immediate medical attention. Following
this rule will reduce the risk of serious personal injury.
 Save these instructions. Refer to them frequently and use
them to instruct others who may use this product. If you
loan someone this instrument, loan them these instructions
also.
The following signal words and meanings are intended to
explain the levels of risk associated with the product.
SYMBOL / SIGNAL
DANGER:
WARNING:
CAUTION:
CAUTION:
Some of the following symbols may be used on this product.
Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the tool better and
safer.
SYMBOL / NAME
Safety
Alert
CHARGER
AP4700, AP4500
Read The
AP4800
Operator's
Manual
V Volt
Hz Hertz
W Watt
Direct
Current
Laser
Exposure
Recycle
Symbols
SYMBOLS
MEANING
Indicates an imminently hazardous situ-
ation, which, if not avoided, will result in
death or serious injury.
Indicates a potentially hazardous situa-
tion, which, if not avoided, could result in
death or serious injury.
Indicates a potentially hazardous situa-
tion, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates
a situation that may result in property
damage.
DESIGNATION/
EXPLANATION
Indicates a potential personal injury
hazard.
To reduce the risk of injury, user must
read and understand operator's
manual before using this product.
Voltage
Frequency (cycles per second)
Power
Type or a characteristic of current
Laser radiation - avoid direct eye
exposure.
This product uses lithium-ion (Li-
ion) batteries. Local, state or fed-
eral laws may prohibit disposal of
batteries in ordinary trash. Con-
sult your local waste authority for
information regarding available
recycling and/or disposal options.
FEATURES
PRODUCT SPECIFICATIONS
Battery Pack Voltage ..................................................... 4 V DC
Laser Certifications ................... Class IIIa, <5mW, 630-670nm
Horizontal Line Accuracy ............................ +/- 1/8 in. at 15 ft.
Vertical Line Accuracy ................................. +/- 1/8 in. at 12 ft.
Upper Dot Accuracy.................................... +/- 1/4 in. at 15 ft.
Lower Dot Accuracy .................................... +/- 1/4 in. at 15 ft.
KNOW YOUR PLUMB/CROSS LASER
See Figure 1.
The safe use of this product requires an understanding of the
information on the product and in this operator's manual. Before
use of this product, familiarize yourself with all operating features
and safety rules.
DUAL FUNCTION LASER
Your plumb/cross laser features a combination of plumb dot
and cross hair laser for window installation, stud wall, tiling, and
other applications.
FINE HEIGHT ADJUSTMENT
Your plumb/cross laser features an adjustment for fine-tuning
the laser lines.
LASER PENDULUM LOCK
When your plumb/cross laser is fully seated into the outer jacket,
it locks into position to prevent damage when transporting the
product.
OUT-OF-LEVEL INDICATOR
The laser line turns off and the backlight blinks when the pendulum
it is out-of-level to prevent inaccurate readings.
SELF LEVELING
The plumb/cross laser automatically sets itself to level position
when the unit is lifted from the outer jacket and into operating
position.
TRIPOD-MOUNT READY
Your plumb/cross laser has a tripod mount built into the outer
jacket.
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
 Carefully remove the product and any accessories from the
box. Make sure that all items listed in the packing list are
included.
WARNING:
Do not use this product if it is not completely assembled
or if any parts appear to be missing or damaged. Use of a
product that is not properly and completely assembled could
result in serious personal injury .
 Inspect the product carefully to make sure no breakage or
damage occurred during shipping.
 Do not discard the packing material until you have carefully
inspected and satisfactorily operated the product.
 If any parts are damaged or missing, please call
1-800-525-2579 for assistance.
PACKING LIST
Plumb/Cross Laser
Soft Case
Operator's Manual
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories
not recommended for use with this product. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.