Audiovox Prestige PLATINUM APS-700 Guia De Instalacion página 7

Connecting And Adjusting The Shock Sensor:
Route the 4 pin cable from the previously installed shock sensor to the control module. Plug it into the mating 4 pin white
connector shell located along side the 8 pin main harness connector of the control unit.
Pre- adjust the previously installed Shock Sensor by first accessing the potentiometer setting screw and carefully turn this
adjustment all the way counterclockwise. Now Turn the adjuster clockwise to the first notch on the module case.
CAUTION! Use caution when striking the vehicle and around the glass panels. Impact tolerances of vehicle glass differs from
vehicle to vehicle. This test can also be made by striking the vehicle bumpers providing you consider the amount of force
required to break a window.
Exit the vehicle, close all doors, hood and trunk and arm the alarm system.
Firmly strike the windshield pillar with the open palm of your hand. If the alarm system triggers, disarm then re-arm the
system and make the same test on the rear window support. If the system triggers, no further adjustment is necessary.
If in the above test the sensor did not trigger the alarm system, carefully move the adjustment potentiometer in a clockwise
direction and re-test in the same manner until the desired results are achieved.
Confirm the Alarm's operation by arming the alarm, testing an entry point then disarming. Follow this sequence until all
protected areas have been tested. While testing, observe the operation of the parking lights for proper operation, confirm that
the siren chirp patterns for arm, disarm, disarm after intrusion and arm while a door is open are operating properly. If
headlight illumination is used, check to insure proper operation.
RF Programmable Features:
Feature Selection
First
Second
Third
Fourth
Fifth
Sixth
To Program The Alarm's Selectable Features:
Action
Turn the ignition switch on
Flip the valet/program switch on then off 3 times
Within 3 seconds, turn the ignition switch off,
then on
Press transmitter button 1 to change.
First
Or
Flip valet/program switch on then off
Press transmitter button 1 to change.
Second
Or
Flip valet/program switch on then off
Press transmitter button 1 to change.
Third
Or
Flip valet/program switch on then off
Press transmitter button 1 to change.
Fourth
Or
Flip valet/program switch on then off
Press transmitter button 1 to change.
Fifh
Or
Flip valet/program switch on then off
Press transmitter button 1 to change.
Sixth
Or
Flip valet/program switch on then off
Or
Turn ignition switch off.
NOTE: Once you've entered the program mode DO NOT allow more than 15 seconds to pass between steps, or the program-
ming mode will be terminated.
ALARM SELECTABLE FEATURES
1 Chirp
1 Second Door Locks
Auto Lock On
Auto Unlock On
Headlight Output On
Passive Door Locks
Passive Arming
2 Chirp
3.5 Second Door Lock
Auto Lock Off
Auto Unlock Off
Headlight Output Off
Active Door Locks
Active Arming
System Response
No Response
1 Chirp-LED 1 Flash
Short Chirp, then Long Chirp
1 Chirp = 1 second Locks
2 Chirps = 3.5 second Locks
2 Chirps = auto locks off
1 Chirp = auto locks on
2 Chirps = auto unlock off
1 Chirp = auto unlock on
1 Chirps = headlight o/p On
2 Chirp = headlight o/p Off
2 Chirps = Active Locks
1 Chirp = Passive Locks
1 Chirp = passive arming
2 Chirps = active arming
Exit Program Mode
Exit Program Mode
7
Default
1 Second
Auto Lock Off
Auto Unlock Off
Headlights On
Active Door Locks
Passive Arming
LED Flash Pattern
1 Flash Pause etc.
2 Falsh Pause etc.
3 Flash Pause etc.
4 Flash Pause etc.
5 Flash Pause etc.
6 Flash Pause ect.