Knape & Vogt TSC12-1-35 Instrucciones De Instalación

Parts Included
A. One (1) Sliding Bin Assembly
(Slide brackets, sliding members,
slide covers and platform pre-
assembled)
B. Waste Bins (2)
C. One (1) Wire Accessory Basket
(only on single-bin models)
D. Two (2) Rear Slide Mounting
Brackets
E. Door Brackets (two pair)
F. Four (4) #6-18 x 5/8" Phillips
flathead sheet metal screws for
mounting door brackets
G. Four (4) #10-24 x 1/4" Phillips pan
head machine screws
H. Eight (8) #7 x 1/2" Phillips pan head
sheet metal screw for mounting
slide members
I. Slide Members
Single Bin
Rear Slide Double Bin
Mount Platform
Platform
and Basket
Brackets
Slide
Members
Face
Frame
Bracket
Disconnect
Face
Frame
Door
Adapter
Brackets
Tools Required
drilling pilot holes
Product Assemblies
TSC12-1-35 TSC15-2-35
TSC15-1-35 TSC18-2-35
TSC15-1-50
2700 Oak Industrial Drive NE, Grand Rapids, MI 49505 USA
TOP-MOUNT SOFT-CLOSE
WASTE AND RECYCLING UNIT
Installation Instructions
Note: This product is designed specifically for use with traditional face frame style cabinetry. To
use with non-traditional face frame cabinetry, or Euro-style frameless cabinetry, additional
blocking may be required to provide the correct cabinet opening width.
Inspect all parts and read all instructions prior to beginning assembly and installation.
If cabinet door is attached to cabinet, remove
1
hinges from cabinet frame and door, and set door
aside for use in Step 6.
Mark the locations for attaching the front of slides.
On face frame cabinetry, make one mark 13-3/8"
(for 35 qt. applications) OR 17-7/16" (for 50 qt.
applications) up from the interior cabinet floor on
both the left and right face frame stiles. These marks
indicate the top-hole locations on the face frame
brackets (figure A). Draw a level line on these marks.
Make another mark 3/4" lower on both the left and
right face frame stiles. This will be 12-5/8" (for 35 qt.
applications) OR 16-11/16" (for 50 qt. application)
up from the interior cabinet floor. These marks
indicate the bottom hole locations on the face
frame brackets (figure A). Draw a level line on
these marks.
To properly locate the slide front to back, draw a
second set of marks on the drawn level lines 1/2"
back from the front of the face frame. The
intersection of these marks and the drawn level lines
indicates the location of the front mounting screws
for both the left and right slides.
Slide
Member
Optional Step
Brackets
Using 1/16" drill bit, drill pilot holes for inserting screws.
2 Mark rear location for attaching slides. On face frame cabinetry, measure 14-7/8" (for 35 qt.
applications) OR 18-15/16" (for 50 qt. applications) up from the cabinet bottom on the cabinet
back panel. If you have a recessed cabinet bottom that sits below the top of the bottom face
frame rail, you will need to add the amount of face frame reveal to this number. Mark this
location. (Example: cabinet bottom is 1/4" below the top edge of face frame = 14-7/8" + 1/4"
equals 15-1/8" high mark). Using a level, verify that both marks on cabinet back panel are level.
Determine and mark the centerline of the back panel of cabinet. Place rear bracket
3
installation template on back panel so that the height line on the template lines up with the
your back panel. The centerline of the rear bracket installation template must also line up with
the center line you made on the back panel of the cabinet. Tape rear bracket installation
template to back panel. Verify that the centerline and height line on template still line up with
centerline and height line on rear panel of cabinet. Refer to the chart on rear bracket
installation template to determine the distance from the centerline to the inside edge of each
slide mounting bracket for your product assembly. You will also see this same measurement in
Chart 1 below, for reference. Using a punch, mark holes for inserting screws to mount rear
sheet metal screws, attach either the left of right rear bracket to rear panel of cabinet. Repeat
this process for attaching other rear bracket.
CHART 1
Product Assembly
TSC12-1-35
TSC12-1-35
TSC15-1-35
TSC15-1-35
TSC15-1-50
TSC15-1-50
TSC15-2-35
TSC18-2-35
TSC18-2-35
* Tolerance is +1/32" - 0"
Cabinet Opening Distance from Centerline*
11-1/2"
12"
14-1/2"
15"
14-1/2"
15"
15"
17-1/2"
18"
FIGURE A
Adapter Required
4-7/16" No
4-7/16" Yes
5-15/16" No
5-15/16" Yes
5-15/16" No
5-15/16" Yes
6-3/16" No
7-7/16" No
7-7/16" Yes
310169-D-0912
2/6