Bayco Products NightStick TWM-354 Manual De Instrucciones

Instruction Manual
TWM-354
Please read these instructions before using your Nightstick TWM-354.
They include important assembly and operating instructions.
PACKAGE CONTENTS
y 1 - TWM Weapon Mounted Light – Long Gun
y 1 – TWM-RPS Remote Pressure Switch Cable
y 1 – NS-PIC1 Picatinny Rail Mount for RPS Switch
y 1 – 2-Part Velcro Pads w/ Pressure Sensitive Adhesive Strips
y 1 – Alcohol Prep Pad
y 2 - CR123 Lithium Batteries
y 1 - Set of Cross Rail Inserts (pre-installed)
y 4 - Cross Rail Mounting Cap Head Screws (pre-installed)
y 1 - Allen Wrench
WEAPON SAFETY
PLEASE BE SURE TO READ, UNDERSTAND AND FOLLOW THESE SAFETY
AND OPERATING INSTRUCTIONS WHEN HANDLING A FIREARM OR THE
NIGHTSTICK TWM WHEN MOUNTED ON A FIREARM. FAILURE TO DO SO
CAN BE DANGEROUS AND COULD RESULT IN SERIOUS INJURY, DAMAGE
TO PROPERTY, OR DEATH.
Use of a fi rearm under any circumstance is inherently dangerous. SERIOUS
INJURY OR EVEN DEATH may result without proper training in the safe handling
of fi rearms. Proper training should be obtained from an accredited fi rearms safety
program conducted by a qualifi ed instructor.
Read, understand and follow all of the safety instructions that came with your
fi rearm before attaching your new TWM.
y Always assume every fi rearm is loaded and treat that fi rearm as such.
y Never point a fi rearm at anything that you are not willing to destroy.
y Never service your fi rearm or your TWM when mounted on a fi rearm without
fi rst activating the weapon's safety (if applicable), removing the magazine,
opening the action and physically and visually inspecting to make sure that no
ammunition is installed in the fi rearm.
BEFORE ATTACHING, INSPECTING OR SERVICING THE TWM
y Engage the safety on the fi rearm (if applicable).
y Remove the magazine from the fi rearm (if applicable).
y Open the action and visually and physically inspect the chamber to be sure it
is empty.
y Keep the barrel pointed in a safe direction at all times and never place your
hand in front of the muzzle.
Bayco Products, Inc. • 640 South Sanden Blvd. • Wylie, TX 75098 • 1-800-233-2155 • 1-469-326-9400 • www.nightstick.com
WARNING: IT IS IMPERATIVE THAT SAFETY MEASURES BE EMPLOYED AT
ALL TIMES WHILE HANDLING A FIREARM.
WATCH COMPLETE INSTALLATION VIDEO AT: HTTPS://YOUTU.BE/
JR8RP194DSG
INSTALL BATTERIES
Image 1
y Open the Battery Door Screw using a Phillips head screwdriver. (Image 1)
y Insert the included CR123 Batteries using the battery orientation markings on
the side of the light. (Image 2)
y Re-install the Battery Door Screw until fully tightened. (Image 3)
INSTALLING RPS CABLE ONTO THE TWM
Image 4
y Insert the connector of the RPS Cable into the mating connector on the Battery
Door of the TWM until it is fully inserted. (Image 4)
y Screw the Threaded Coupling Ring on the end of the RPS Cable onto the
external threads on the TWM Battery Door in a clockwise direction by hand until
it is fully tightened. CAUTION: Do not cross-thread, do not use any tools to
tighten (fi nger tight only) or strip the screw threads. (Image 5)
INSTALLING THE TWM ON TO YOUR FIREARM
Your TWM comes with both cross rail inserts pre-installed in cross rail slots 1 & 4.
y If the location of one or both of these is not correct for your specifi c installation,
remove either or both of the inserts and then proceed to step 1.
y If the location of the pre-installed inserts is correct for your fi rearm, proceed
to step 3.
WARNING: DO NOT INSTALL THE TWM ONTO A FIREARM WITHOUT
USING THE CROSS RAIL INSERT. FAILURE TO USE A CROSS RAIL
INSERT COULD RESULT IN THE TWM COMING LOOSE FROM THE
FIREARM UNDER EVEN NORMAL RECOIL.
STEP 1: DETERMINE WHICH CROSS RAIL INSERT SLOT TO USE
Image 7
y Hold the TWM alongside the Picatinny rail on your fi rearm and determine which
of the 4 Cross Rail Insert Slots milled into the top of the TWM is best suited for
your fi rearm. (Image 6)
y A single Cross Rail Insert can be installed in any of the 4 Cross Rail Insert Slots
milled into the top of the TWM.
y Slots 1, 3 & 4 (Image 7) are set up at a standard 1913 spacing, meaning that
all 3 will line up with a Mil-STD-1913 Picatinny Rail. If the desired installation
location on your fi rearm will allow it, both of the 2 included Cross Rail Inserts may
be installed in any combination of slots 1, 3 or 4. Using both of the Cross Rail
INS-TWM-354-20
Image 2 Image 3
Image 5
Image 6
Image 8 Image 9