Care And Cleaning - Crane Plumbing 3782-28 Guia De Inicio Rapido

10
TANK
LEVER
FLOAT
CUP
FILL
VALVE
FLAPPER
THREADED
SHANK
LOCK NUT
COUPLING NUT
(HAND TIGHT ONLY)
12
NOTE: Pictures are representative and may not
exactly depict the flush valve.
LIFT ARM
FIRST
IMPORTANT: Always
clear sand and rust
from system.
• Make sure water supply
is off. Remove valve TOP
by lifting arm and rotating
top and arm 1/8 turn
counterclockwise,
pressing down slightly
on cap.
Always use quality Fluidmaster repair parts when maintaining your Fluidmaster products.
Fluidmaster shall not be responsible or liable for any damages caused by products used
with Fluidmaster valves that were not manufactured by Fluidmaster, Inc.
13

CARE AND CLEANING

When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid
detergents, disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on
your toilet seat. Some bathroom chemicals and cosmetics may damage the seat's finish.
!
WARNING:
Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage
fittings in the tank. This damage can cause leakage and property damage.
Crane shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing
chlorine (calcium hypochlorite).
REFILL
TUBE
HOOK
FLUSH
VALVE
Diagram 1
• While holding a • Replace TOP by engaging
container over the lugs and rotating 1/8 turn
uncapped VALVE to
clockwise. MAKE
prevent splashing, turn
CERTAIN TIP IS TURNED
water supply on and off TO THE LOCKED
a few times. Leave POSITION. VALVE MAY
water supply off. NOT TURN ON IF TOP IS
NOT FULLY TURNED TO
THE LOCKED POSITION.
ADJUSTMENTS
a. Adjust water level. Water level
should be adjusted to level indicated
on tank by adjusting float cup.
See Step 11 for water level adjustment
method
b. If bowl fails to siphon, an adjustment
may be required with the lift chain.
Simply remove the bead chain from
the retainment clip (see Fig. 10A)
and take up slack on the chain, and
reinsert on lift rod. Make sure the
chain is not too taught.
IF FILL VALVE SHUTS OFF BUT CONTINUES TO LEAK
SLOWLY, repeat Step 12.
IF FILL VALVE TURNS OFF AND ON DURING PERIODS OF
NON-USE, it is a signal you are wasting water because:
• The end of the refill tube is inserted into overflow pipe, below
water level in tank. Attach refill tube to overflow pipe using "S"
clip provided.
• The flush valve is leaking because it's worn, dirty or misaligned
with tank ball or flapper (replace with a new flapper).
IF FILL VALVE WON'T TURN ON OR SHUT OFF or REFILL
OF TANK WATER IS SLOW after valve has been in use for
some time, Fluidmaster Model 242 Replacement Seal may be
needed.
Go to our website at www.fluidmaster.com for more
solutions to toilet problems.
For troubleshooting information please contact:
San Juan Capistrano, CA 92675
(949) 728-2000 (800) 631-2011
- 3 -
11
Turn on water supply. Let the
toilet cycle once. Adjust the
water to desired level by
depressing TAB on FLOAT CUP
and moving FLOAT CUP up or
down.
TROUBLESHOOTING
30800 Rancho Viejo Road
www.fluidmaster.com
© 2001 Fluidmaster, Inc.
® Registered trademark of Fluidmaster, Inc.
TAB
FLOAT
CUP
7 3 018 3 0 - 10 0