Technical Data - Vanderbilt SPCN340 Instrucciones De Instalación

English – Instructions
This device must only be connected to SPC42xx/43xx/52xx/53xx/63xx.
EC Declaration of Conformity
Hereby, Vanderbilt International (IRL) Ltd declares that this radio equipment
type is in compliance with all relevant EU Directives for CE marking.
•
EMC directive:2014/30/EU
•
LVD directive: 2014/35/EU
•
RE directive (RED): 2014/53/EU
The full text of the EU declaration of conformity is available at
https://vanderbiltindustries.com/compliance-documents
Package contents
•
SPCN340 x1
•
Antenna x 1
•
Mounting pillar x 4
Product overview
The SPCN340 modem provides the SPC controller with a GSM (4G) interface. The
modem supports 4G and 2G communications, enabling IP communications to
central station software, SPC Connect, and mobile technologies. Analogue central
stations are also supported for SIA, Extended SIA, Contact ID, and Fast Format.
The "Pay As You Go" (PAYG) credit balance can also be read by SPC controller
when a PAYG SIM is used with a provider that supports USSD credit checks.
For a description of the GSM (4G) features please consult the SPC4xxx/5xxx/6xxx
Installation & Configuration Manual.
Installing the SPCN340
When replacing or installing modules on the SPC system, always ensure
that the mains supply and the battery are disconnected. Ensure that all anti-
static precautions are adhered to when handling connectors, wires,
terminals and PCBs.
Do not reduce the standard-size SIM card to micro- or nano-size.
The SPCN340 must have a standard-size SIM card installed in the unit to operate.
The SIM card must be in the holder before power is applied to the SPC system
(see below for details on installing the SIM card).
See Fig. 1: SPCN340
A Controller PCB (Printed Circuit Board)
B SPCN340 in the primary slot on the controller PCB
C SMA connector for antenna
D Secondary slot
Before installing the GSM (4G) module onto the SPC controller, ensure that a
functioning SIM card is installed on the module.
See Fig. 2: Insert SIM Card
A SIM card holder
B SIM card
C Flap on SIM card holder
To insert a SIM card into the GSM (4G) module:
1. Place a finger on the SIM card holder (Fig. 2, Item A) and slide the SIM card
holder flap (Fig. 2, item C) to the right
2. Rotate the SIM card holder flap to the 'up' position
3. Slide the SIM card (Fig. 2, Item B) into the SIM card holder flap.
4. Rotate the SIM card holder flap back to its original position.
5. Press and slide the SIM card holder flap to the left to click into place.
Make a note of the unlock code for your SIM card. The code is required
when enabling the SIM card on the SPC system.
To install the SPCN340 (with SIM card):
1. Ensure the AC mains power and battery backup connections are removed.
2. Insert the push-in mounting pillars (included with the module) into the four hole
positions on either the primary slot (left) or secondary slot (right) on the
controller.
3. Align the 16-pin female socket over the 16-pin male connector, ensuring that
the holes on the SPCN340 are aligned with the top of the mounting pillars.
4. Firmly but gently press down to secure the module.
5. Attach the antenna (supplied) to the SMA connector (Fig. 1, item C) on the
GSM (4G) module.
For new system installations, consider removing the knock-out for the
antenna prior to mounting the housing on the wall.
6. Mount the antenna on the top of the housing using one of the 12mm knock-out
holes provided. The 12mm knock-out holes align with the primary slot (left) and
secondary slot (right). Ensure that the antenna is unobstructed.
7. Restore the AC mains power and battery backup connections to the controller.
LED Functionality
There are six LEDs on the top of the modem module labelled D1 to D6 (See Fig.
3). These are used to indicate the status of the modem.
The function of each LED is as follows:
LED State Indicates
D1 Flashing Power
Green
D2 On Mast
Green connection
D3 On Data
Green Transmission
Configuring the SPCN340
For configuration instructions, please refer to the Configuring Modems sections of
the SPC4xxx/5xxx/6xxx Installation & Configuration Manual.
For 4G performance ensure that the panel firmware is updated with version
3.11 or later.

Technical Data

Network connection 4G: 800MHz/900MHz/1800MHz
2G: 900 MHz/1800MHz
Operating current Max. 130 mA at 12 VDC
Quiescent current Max. 40 mA at 12 VDC
Operating temperature -10 to +50 °C
Relative humidity Max. 90 % (non-condensing)
Mounting Plug on module to SPC controller
Dimensions (W x H x D) 90mm x 38mm x 25mm (PCB)
Weight 0.130 kg
Pending: EN
Standards / approval
Ordering Information
SPCN340.000 GSM (4G) Module incl.
Antenna
SPCW101.000 External aerial kit
Dansk – Instruktioner
Denne enhed må kun tilsluttes en SPC central
SPC42xx/43xx/52xx/53xx/63xx
EN Direktiver og godkendelse
Hermed erklærer Vanderbilt International (IRL) Ltd, at denne transmissions
enhed er i overensstemmelse med følgende EU-direktiver for CE-mærkning:
•
Direktiv 2014/30 / EU (EMC Direktivet)
•
Direktiv 2014/35 / EU (lavspændingsdirektivet)
•
Direktiv 2014/53/EU (radioudstyrdirektivet)
Den fulde ordlyd af EU-overensstemmelseserklæringen er tilgængelig på:
https://vanderbiltindustries.com/compliance-documents
Pakkens indhold
•
SPCN340 x1
•
Antenne x 1
•
Monterings stag x 4
Produkt beskrivelse
SPCN340-modemmet giver SPC-centralen et GSM-interface (4G). Modemmet
understøtter 4G- og 2G-kommunikation, der muliggør IP-kommunikation til
kontrolcentraler, SPC Connect og mobile teknologier. Analoge kontrolcentraler
understøttes også for SIA, Extended SIA, Contact ID og Fast Format.
Kreditsaldoen for "Pay As You Go" (PAYG) kan også aflæses af SPC-centralen,
når et PAYG-SIM-kort anvendes med en udbyder, der understøtter USSD-
kredittjek.
Hvis du ønsker en beskrivelse af GSM-funktionerne (4G), se da manualen
installations- og konfigurationsmanualen til SPC4xxx/5xxx/6Xxx.
Installation af SPCN340
Ved udskiftning eller installation af moduler på SPC-systemet skal det altid
sikres, at strømforsyningen og batteriet er frakoblet. Sørg for, at alle
antistatiske forholdsregler overholdes ved håndtering af stik, ledninger,
klemmer og printkort.
Reducer ikke SIM-kortets standardstørrelse til mikro- eller nanostørrelse.
SPCN340-enheden skal have et SIM-kort i standardstørrelse installeret for at
kunne fungere. SIM-kortet skal sidde i holderen, før SPC-systemet strømforsynes
(se oplysninger nedenfor om, hvordan SIM-kortet installeres).
Se fig. 1: SPCN340
A Centralens printkort
B SPCN340 i det primære slot på centralens printkort
C SMA-stik til antenne
D Sekundært slot
Før GSM-modulet (4G) installeres på SPC-centralen, skal det sikres, at der er
installeret et fungerende SIM-kort på modulet.
Se fig. 2: Indsæt SIM-kort
A SIM-kortholder
B SIM-kort
C Flap på SIM-kortholder
LED State Signal Strength
D4 Off Low 1
Red
Flashing Low 2 - 3
On Medium 4 - 5
D5 Flashing Medium 6
Amber
On High 7
D6 Flashing High 8
Green
On Very High 9
V54550-B102-A300
V54559-B101-A100