Prime EZ-SET TNIWP Guia De Inicio Rapido

EZ-SET DIGITAL
IN-WALL TIMER
Call customer service at 1-888-445-9955,
8 a.m. - 5 p.m., PST, Monday - Friday.
IMPORTANT PRODUCT INFORMATION
Single Pole: Timer will control devices from one location.
Do not use in a 3-Way application where multiple switches
control the same device.
Neutral Wire: Must be available as part of the wiring of
the building. Timer will not function properly if a neutral
wire is not available.
Direct Wire: This timer is only intended to be permanently
installed into an electrical wall box.
Tool Required: One (1) standard flathead screwdriver.
(not included)
PROGRAMMING INSTRUCTIONS
STEP 1 - Set the time
• Use the up ( ) and
down ( ) arrow to set the
current time.
ADDITIONAL FEATURES
CUSTOM COUNTDOWN:
• Press "CTD".
• Press up ( ) and down ( ) arrow to set the
countdown from 1 minute to 24 hours.
(Note: "CTD" will flash on LCD to indicate the
countdown feature is active)
MODEL #TNIWP
INSTALLATION INSTRUCTIONS
1. Turn off power at circuit breaker or fuse box before
uninstalling existing device or installing new timer.
2. Remove existing wall plate and switch from wall box.
3. Make sure the following 3 wires are present in the wall
box. (see Diagram A)
i. 1 Hot Wire from circuit breaker box
ii. 1 Load Wire to the device to be powered
iii. 1 Neutral Wire
If one or more of these are not present, this timer will
not function properly. Additional wiring to the wall box
will be required before installation of this timer can be
completed.
4. Strip wires 1/2 inch long. (see Diagram A)
5. Use the included wire nuts and securely twist together
to attach the timer wires to the building wires. (see
Diagram A)
6. Insert timer into wall box (2-1/2 inch) being careful not to
pinch any wires. Be sure timer is upright with LCD
screen located at the top of the timer. (see Diagram B)
7. Fasten timer to the wall box using screws provided.
(see Diagram B)
8. Place rocker/decorator wall plate around the timer face.
(see Diagram B)
9. Restore power at circuit breaker or fuse box.
STEP 2 - Pick a preset option
• Press one or more of the
preset options that meet your
Custom needs.
ON
• When the button lights up
the timer is set (timer must
Custom
be hardwired into an
OFF
electrical wall box for buttons
5am-8am
to illuminate).
5pm-12am
• If you would like a custom
On to step 2 on/off time, move to Step 3.
5pm-8am
If not, the setup of your new
ON/OFF CTD
EZ-SET timer is FINISHED!
MANUAL ON/OFF OVERRIDE:
• Press "On/Off" to bypass the current setting and turn
your device On or Off.
(Note: Timer settings will resume based on the next
programmed cycle)
From Timer
Black Wire
Red Wire
White Wire
Green Wire
*
or to ground post or screw terminal
Custom
ON
STEP 3 - Set a Custom
On/Off Time
• Hold down "Custom ON"
Custom
OFF
and press the up (
5am-8am
down (
ON time.
5pm-12am
• Hold down "Custom OFF"
5pm-8am
and press the up (
down (
ON/OFF CTD
OFF time.
• Press, BUT DO NOT
On to step 3
HOLD DOWN, the "Custom On" and "Custom Off"
buttons. Buttons will turn blue when the program
is activated.
Hot Wire Black Wire
Load Wire
White Wire
Neutral Wire
Red Wire
Ground Wire
Green Wire
Diagram A
Diagram B
In Wall Box
Hot Wire
Load Wire
Neutral Wire
*
Ground Wire
Custom
ON
) and
Custom
) arrow to set the
OFF
5am-8am
Custom
ON
5pm-12am
) and
5pm-8am
Custom
) arrow to set the
OFF
ON/OFF CTD
5am-8am
5pm-12am
5pm-8am
ON/OFF CTD
03-08292018