Steren K-435 Manual De Instrucciones página 2

Before using your new Steren´s product, please read this instruction
manual to prevent any damage.
I M P O R T A N T
The instructions of this manual are for reference about the product. There may
be differences due to updates.
Please check our website (www.steren.com) to obtain the latest version of the
instruction manual.
• Do not expose to direct sunlight or extreme temperatures.
• Do not use or store the equipment in places where it might get wet. Can cause
malfunctions.
• The kit contains small parts, do not leave small children to reach.
• We recommend adult supervision when the kit is being assembled as it is required to
use welding and soldering.
• Always use a soft dry cloth to clean the equipment.
H I G H L I G H T S
•
The RGB programmable kit can be easily assembled by students and hobbyists with
basic electronic knowledge. The controller is already programmed with sequences,
you just need to assemble and enjoy their functioning.
• What is more, it can be used for advanced knowledge people, because you can
create sequences and reprogramming using PIC-600, without removing the PIC from
the kit using the ISCP port.
• This kit can be upgraded in power output stage, if required, and control more RGB
LED strips.
•
Programmable
•
Preloaded sequences
•
PCB ready to be upgraded
I N S T R U C T I O N S
Clip 9V
Assemble the components according to the following suggested order.
1. Resistors R1 to R5.
2. Micro switch button.
3. Microcontroller base.
4. The C1 and C2 capacitors.
5. LEDs, R - red, G - Green, B - blue.
6. ICSP strip pin.
7. Female PCB plug.
8. The IC1 regulator.
9. Square battery clip first pass wires through the hole to secure.
10. Connect a square battery and check the voltage at the regulator terminals; must have 9V
between pins 1-2, and 5V between pin 2 and 3, remove the square battery.
11. Insert the PIC (IC2) at its core, be careful with orientation.
12. Reconnect the battery and your kit should begin to work.
O P E R A T I O N
- The K-435 operation is done by the S1 button as described below.
- One click: pause / continue , the sequence stops and maintains fixed the color that is
currently displayed, pressing the button again will continue running the sequence.
- Double click: next sequence, advances to the next programmed sequence, when it reaches
the last one, it will begin at the first again.
- Long Click: turn off / on , if the button is pressed for 1.2 seconds the K-435 will enter
suspended mode (off), if pressed again it for 2 seconds, it will turn on.).
You will notice that the basic kit comes without Q1 to Q3, R6 to R11 and without power
connection terminals, this is because, if you wish, you can purchase these components
separately and install them to have outputs up to 5 Amps per channel, in addition to
the possibility of integrating all the kit in a GP-16 box for which it already has the exact
dimensions.
Do not look front LEDs when they are powered on, they could cause damage or irritation
to the eyes.
Refer to the documentation and tutorials related to this K-435 kit at www.steren.com
M A T E R I A L L I S T
ID DESCRIPTION
PCB Printed circuit board
IC1 5V regulator
IC2 PIC Microcontroller
8-Pin DIP base
C1 220 nF ceramic capacitor (224)
C2 100 nF ceramic capacitor (104)
R1, R2 10K ohm 1/4W resistor (brown, black, orange)
R3 180 Ohms 1/4W resistance (brown, brown)
R4 330 Ohms 1/4W resistance (orange, orange, brown)
R5 120 ohm 1/4W resistance (brown, red, brown)
R Ultra-bright red LED
G Mega brilliant Green LED
B Ultra-bright blue LED
ICSP 5-pin strip
S1 PB micro switch
BAT 9V battery clip
ALIM 2.1 mm female plug for PCB
ALIM1, RGB Three screw terminal
R6, R8, R10 47K Ohms 1/4W resistor
R7, R9, R11 120 ohm 1/4W resistance
Q1, Q2, Q3 N Channel MOSFET
S P E C I F I C A T I O N S
Input: 9 V- - - (square battery)
12 V- - - 3 A (extended power output version)
Product design and specifications are subject to change without notice.
Product: RGB LED strip controller kit
Part number: K-435
Brand: Steren
This Steren product is warranted under normal usage against defects in workmanship and materials to the original purchaser for one year from
the date of purchase.
1. This warranty card with all the required information, invoice or purchase ticket, product box or package, and product, must be presented when
warranty service is required.
2. If the product is in the warranty time, the company will repair it free of charge.
3. The repairing time will not exceed 30 natural days, from the day the claim was received.
4. Steren sell parts, components, consumables and accessories to customer, as well as warranty service, at any of the addresses mentioned later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling, leaky batteries, failure to follow enclosed instructions, improper repair by
unauthorized personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
RETAILER INFORMATION
Name of the retailer ____________________________________
Address _____________________________________________
Product ______________________________________________
Brand _______________________________________________
Serial number _________________________________________
Date of delivery _______________________________________
In case your product fails or have questions, please contact your nearest dealer. If you are in Mexico, please call to our Call Center.
A T E N T I O N
PART No.
MC7805CT
12F629
IC8P
C.22-16
C.1-50
R10K 1/4
R180 1/4
R330 1/4
R120 1/4
ULTRA 5/RED
E5/GREEN-MEGA
5/BLUE ULTRA
F36-S
AU-101
258-810
OPTIONAL TRTG-03
OPTIONAL R47K 1/4
OPTIONAL R120 1/4
OPTIONAL IRF640
WARRANTY
CONDITIONS
01 800 500 9000
CANT.
1
1
1
1
1
1
2
1
1
1
1
1
1
5/36
1
1
1
2
3
3
3