AmerTac Westek DIY Serie Instrucciones De Instalación

DIY Series LED Undercabinet Lighting
Models: MRGOL12W, MRGOL16W and MRGOL22W
FEATURES
Plug-in design for easy installation
Quick and easy linking system
Dimmable Long Life LED technology
On/Off Switch
INCLUDES
MRGO Series Plug-in Light Fixture (12" or 16" or 22")
5' Power Cord, 12" Linking Cord, Mounting Hardware and (2) Screw Plugs.
IMPORTANT SAFETY INSTRUCTIONS
For use with 120V, 60Hz electrical power supply only.
WARNING: TO PREVENT OVERHEATING AND ELECTRICAL SHOCK DO NOT INSTALL IN SMALL ENCLOSED SPACES. TO
PREVENT ELECTRICAL SHOCK DO NOT INSTALL IN WET LOCATIONS.
SAVE THESE INSTRUCTIONS
1. Read and understand all of these instructions before installing fi xture.
2. Keep these instructions in a safe place for future reference.
3. Do not mount over sink or stove.
4. WARNING: These products may represent a possible shock or fi re hazard if improperly installed or attached in any way.
Products should be installed in accordance with these instructions, current electrical codes and/or the current National
Electric Code (NEC).
SECTION 1 - PREPARATION FOR INSTALLATION
Tools Needed
Parts of this Light Fixture
This light fi xture comes with a the 5' Power Cord with a polarized plug (one blade wider
than the other) as a safety feature. This plug can be used in a polarized outlet only one
way. If the plug does not fi t fully in the outlet, reverse the plug. If it still does not fi t, contact
a qualifi ed electrician. Never use with an extension cord unless the plug can be fully
inserted. Do not alter the plug. Become familiar with the parts of the light fi xture. See
Figure 1.
- Mounting holes go through light fi xture to make it easy to locate where to drill pilot
holes for screws or for plastic anchors (not included) if installing in drywall.
- On/Off switch
- Screw Plugs to cover screws for a clean installation.
- Input Panel Cover can be removed to plug in 5' Power Cord for connection to 120V
polarized outlet. The 12" linking Cord is used to link fi xtures together. The Output Panel
Cover can be removed to plug in the other side of the 12" linking Cord to link fi xtures
together. See Figure 2.
Placement of Fixture
Determine location for connecting to nearest 120V polarized receptacle. (Note: before
mounting to cabinet be sure fi xture is within 5' of an electrical outlet, considering path
cord will take to be neatly and securely mounted to cabinet and wall.) If you are not sure
about this installation consult a local licensed electrician or electrical contractor before
proceeding.
Locate Mounting Holes: Place fi xture on mounting surface and with a thin screwdriver,
pencil or scratch awl mark the spot where the screws will be located through the Mounting
Holes in the top of the fi xture. See Figure 3. Do the same for a multiple fi xture installation.
For mounting into drywall, drill 3/16" holes for the plastic wall anchors (not included). Insert
the plastic wall anchors into the proper holes and tap them into place so they are fl ush
with the surface of your drywall. For mounting into wood cabinets drill 1/16" pilot holes,
1/2" deep. Caution: Check your cabinet thickness fi rst. Be careful not to drill through
cabinet.
Prepare fi xture for installation by turning screws provided into mounting holes in the top of
the fi xture so they protrude through the back of the about an 1/8". This will help you line up
screws to mounting holes.
INSTRUCTIONS FOR INSTALLATION OF
PLUG-IN LIGHTING FIXTURE
SECTION 2 - INSTALLATION
Plug-in Fixture Installation
Attach fi xture to cabinet or wall by tightening screws securely. Insert screw plugs for a
clean installation. Connect 5' Power Cord to the Input port after removing Input Panel
Cover. (See Figure 2). Plug in Power Cord to a 15A circuit grounded outlet. Warning: Do
not conceal power supply cord inside a wall, ceiling, soffi t, kitchen cabinet, or similar
permanent structure. Do not run the power supply cord through holes in walls, ceilings or
fl oors.
Use UL listed cable staples (not included) to route Power Cord to bottom of cabinet and
wall for a clean installation.
Interconnecting Multiple Fixtures
WARNING: In multiple fi xture installations do not electrify fi xture group until all electrical
connections have been made And fi xtures have been securely mounted.
MRGO Series fi xtures may be interconnected using either the 12" Linking Cord supplied
with this kit. See Figure 4.
Follow instructions above for Plug-In Fixture Installation.
First mount fi xture that receives incoming electrical supply. Remove the Input or Output
Panel Covers as needed. Make sure the Linking Cord on both ends are fully inserted into
ports on both fi xtures. There should be some slack in the Linking Cord so that the electrical
connectors are not stressed in any way. Use cord clips (not included) to keep cord safely
attached to mounting surface.
Output
panel
Screw
Plugs
Mounting holes
On/Off switch
Screw
Input
Plugs
panel
Step 1
Locate Holes
Step 2
Drill Pilot Holes
CET
12" Linking Cord