Enjoying Your Chair & General Use; Choosing A Location - HoMedics eLounger EL-200 Manual Del Usuario

Assembly Instructions
Setting up your massage chair is easy to do. Your massage
chair is almost completely assembled. After carefully removing
all the contents from the packaging, inspect the chair and
its components to make sure everything has been received.
Components:
• Chair back
• Chair seat
• Seat cushion
Step 1
Attaching the Seat Cushion
Figure 1
• First, clip the ties holding the power cord to the back of
the seat frame.
• Next, attach the seat cushion to the seat by placing the
cushion fully in the seat and lining up the fabric fasteners.
There is one fastener strip in the seat and the second
wraps around the back edge.
Step 2
Attach the back of the chair to the seat.
• First, locate the 2 cords that are attached to the left side
of chair seat (power cord and output jack) and make
sure they exit from the rear of the seat as shown in
Figure 1
• Next you will need to place the chair back into the seat.
Pick up the chair back with the zipper side facing the
front of the chair and lower the back into the seat so that
the knobs on either side of the back (Fig. 2) lock into the
Figure 2 latches in the chair seat (Fig. 1). The latches are marked
with bright green paint.
• The back will click into place and will sit evenly in the
seat. Once the back is sitting evenly in the chair seat,
confirm that the back and seat are attached correctly
by sitting in the chair and pulling the recline lever on
the right side of the chair (Fig. 3). The chair should
recline easily.
NOTE: If the back does not appear even or the chair does
not recline easily, then you may have engaged the latches
on only one side. To correct this you will need to release
the back as noted below and begin Step 2 again.
Figure 3
6
• Lumbar/Headrest pillow
* Removable softening pad
currently in the backrest.
Step 3
Connect the power source.
• First, securely connect the output jack that is located on
the left rear of the chair seat to the input jack (Fig. 1) in
the lower left rear of the chair back (Fig. 4). Be sure that
the output jack is inserted with the word "Up" facing
upwards. When inserted correctly, the third or middle
horizontal line on the connector will meet the edge of the
input jack (Fig. 4).
• Plug the power cord into a grounded 120-volt outlet. This
product is equipped with a grounded plug and should
only be used with the appropriate outlet. Once all pieces
of the massage chair are in place and the main power
line is plugged in, you may turn the power switch on (Fig. 5).
• The eLounger contains a pass-through electrical outlet with
a maximum wattage of 300W as a convenience feature
(Fig. 5). NOTE: This outlet is an added convenience for
use with items such as the coordinating massaging
ottoman, a laptop, lamp or similar device. It will not
power the chair.
Removing the Back from the Seat
To remove the chair back from the seat:
• First, turn off the main power switch and unplug the unit.
Then remove the output jack from the chair back.
• Locate the levers along both sides of the rear of the chair
seat (Fig. 6).
• Push both at once and lean the chair back forward to
release it from the seat. Tip: Use your body or shoulder
to lean against the back as you depress the levers.
• To reconnect the back to the seat, repeat Step 2.
Enjoying Your Chair and General
Use

Choosing a Location

It is important to choose a location that will allow you to
best enjoy the chair's benefits. The following is required for
the massage chair:
• The chair back should be approximately 1 foot from the
nearest object to recline fully.
• An electrical outlet that is a maximum of 8 feet from
the chair.
Outlet
Power
Switch
7
Insert to
this line
Figure 4
Fuse
Figure 5
Figure 6