eXact PipeCut 280E Instrucciones De Manejo página 16

Environment, Guarantee, Tips
Environment
Separate collection. This product must not be
disposed of with normal household waste. When
your Exact PipeCut 170/1 ?0E machine is worn
out, do not dispose of it with normal household
waste. This product must tie recycled separately. Separate
recycling of used products and packaging facilitale recycling
and recovery of materials. Reusing of recycled materials
helps prevent pollution of environment. According to local
regulalions it is possible to deliver household appTiances to
municipal rubbish depositories or to the dealer when buying
a new product.
Guarantee
Warranty terms valid from 01.01.2015
lf the Exact PipeCut Saw becomes unusable due to materia!
or manufacturing defects within the Warranty Term at our
discretion we will repair the Exact PipeCut Saw or supply
an entirely new or factory
reconditioned Exact PipeCut Saw at no charge.
Warranty Term
The Exact Tools Warranty Term is for 12 months from date
of purchase.
The Warranty is only valid if:
1.) Copy of a dated purchase receipt is returned to the
Authorized Warranty Repair Center or has been uploaded
to our website at the time of warranty registration.
2.) The Exact PipeCut Saw has not been misused.
3.) No attempt has been made by non-approved persons
to repair the saw.
4.) The Exact PipeCut Saw has been used in accordance
wIth the operating, safety, and servicing instructions provide
in the manual.
5.) The Exact PipeCut Saw has been delivered to an
Authorized Warranty Repair Center within the term of the
warranty.
Note: The Exact PipeCut Saw is to be shipped to the
Authorized Warranty Repair Center freight prepaid. lf the
Exact PipeCut Saw is repaired under Warranty the return
shipment will be made freight prepaid. lf the Exact PipeCut
Saw is not repaired under Warranty the retum shipment will
be made freight collect.
Please Note: The following items,services or
misuses are excluded from Warranty claims:
- Saw Blades
- Overload Protection Fuse
- Garbon Brushes
- Gripping Unit Wheels
- Blade Flange
-Attachment Flange
- Pulling Flange Washer
- Normal Wear and Tear
- Errors Due to *Misuse or Accident
- Water, Fire and Physical Damage
- Power Cords
-Adjustment of Adjustment Wheel
*lf a wrong type of generator has been used as power
source
exact
Tips for using Exact PipeCut
saws
Diamond blade should only be used for cutting east iron
J:>ipe. lt is not recommended to cut east iron wilh TCT or
Cermet blades.
G_lean the inside of the blade guards after cutting plastic
pIpe.
Smaller pipe is easily cut by rotating the pipe by hand either
on a table or on the lloor. Please note: rotate pipe towards
you when rotating by hand and be careful not to rotate too
fast.
Check the condition of the blade regularly.
The cutting procedure is divided into two stages; first saw
through_ the pipe wall, then complete the cut by sawing
arouni:l 11.
Do not overload the saw by cutting continuously. The saw
will be overheated and the metal parts can become burning
hoi. This will also damage the motor and the blade. The
rule is 2.5 minutes in use and 7.5 minutes rest.
Keep the feeding speed constant. This will extend the
lifetime of the blade.For example cutting !ime for a steel
pipe diameter of 6" (170mm)
(5mm) is 15-20 seconds ana for a cast-iron pipe diameter
of 4" (110mm), with a wall thickness of 1/6" (4mm) is 20 to
25 seconds.
Always keep the motor uni! in the upright position. The
yellow mark of the unlock butlon is !tien vis1ble. Never place
!he Pipe Cut Saw on the pipe in the locked / cutting position.
Factors that affect the lifetime of the saw blade:
• materia! of the pipe
• correct blade type for materia! being cut
• correct motor speed setting (model 170E)
• wall thickness of the pipe
• feeding speed
• smootfiness of the pipe
• user's general skills
• cleanness of the pipe
• rust on the pipe
• welded seam in the pipe
• blade speed
Factors that affect the straightness of the cut:
• condition of the saw blade
• wall thickness of the pipe
• feeding speed
• smootfmess of the feed
• user's general skills
• cleanness of the pipe
• roundness of the p1pe
• gripper unit too loose or too tight
• olade assembled too tight
Due to continuous product development the
information in this instruction book may change.
We do not give separate notification of changes.
16
and a wall thickness of 1/5"
3