Mark MF 700 Manual De Instrucciones

MF 700, 1500, 1500 DMX
Introduction
•
Damage caused by disregard of certain guidelines in th is manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
•
A qualified technician should install and service this device.
•
This device falls under protection class I. It is therefore essential that the device be earthed. Have a qualified person carry out the electric connection.
•
Make sure that the available voltage does not exceed the voltage stated in the specif ications of this manual.
•
Do not crimp the power cord and protect it against damage. Have an authorised dealer replace it if necessary.
•
Disconnect the device from the mains to clean it or when it is not in use. H andle the power cord by the plug only.
•
There may be some smoke or a particular smell when the device is activated for the first time. This is normal and any smoke or smell will gradually disappear.
•
Note that damage caused by user modifications to the device are not covered by the warranty.
•
Keep the device away from children and unauthorised users.
•
Do not direct the device towards anybody.
•
Use adapted smoke liquid only and don't heat the liquid.
•
Make sure there is always enough liquid in the tank; if not the device could overheat.
•
Familiarise yourself with the functions of the device before actually using it. Do not allow operation by unqualified people.
•
Use the original packaging if the device is to be transported.
•
All modifications of the device are forbidden for safety reasons.
•
Only use the device for its intended purpose. Other uses may lead to short circuits, burns, electroshocks etc.
•
Using the device in an unauthorised way will void the warranty.
•
Empty the tank prior to transporting the device.
Installation
a) Smoke Liquid
Please use non-inflammable water-based smoke fluid without oil or grease.
Non-recommended smoke liquid may damage the machine and void the warranty.
1. Unplug the device from the mains.
2. Unscrew the cap from the tank (on top of the device).
3. Carefully pour smoke liquid into the tank; never fill over the "Maximum" mark at the back.
4. Reposition the cap on the tank and close it firmly.
Remark: Do not operate the device when the tank is open.
Operating
Connect the adequate controller in the rear part of the device, depending on the chosen control.
a) Wire Controller
Connect it and wait until the LED lights on. On this moment the fog machine is ready to work. Keep pushed the button to spray smoke. When the LED lights off, the inner relay will wait until the
temperature reachs the correct value, the LED will light on again and the device will be prepared to work again.
b) Timer Controller (MF 1500 DMX)
Connect it and with MINUTE control, set the time intervale (in minutes),when the
device will spray smoke 30 minutes max.). With the SECOND control, it is possible
to set the duration of the spraying in seconds ( 15 seconds max.). The quantity of
sprayed smoke is set with the VOLUME control.
c) DMX-512 Control (Only MF 1500 DMX)
This device uses 1 channel to spray smoke. Connect a DMX
controller in the DMX INPUT connector ( 1: GND, 2: -, 3: +)
DMX OUTPUT allows to link with another DMX device.
Select the DMX starting address using dip switches. The
address is set using the adecuate dip in order to compose
the address number (row: 1,2,4,8,16,32,64,128,256).
For example: Address 25: Move to on dips 1,8 & 16.
Increasing the value of DMX signal, the output volume will increase too.
MODEL
Main Voltage
Power
Re-heating Time
Output
Tank Capacity
Dimensions
Weight
Wire Controller
Timing Controller
Wireless Remote
DMX - 512
Fog Machines
MF 700 MF 1500 MF 1500 DMX
230V AC 50 Hz 230V AC 50 Hz
700 W 1500 W
4.5 Min. 8 Min.
4800Cuft/min. 20000Cuft/min.
0.8 Lt. 2.5 Lt.
336x158x124 mm 475x252x140 mm 417x266x147 mm
4.1 Kg 6.2 Kg
OK OK
X X
X OK
X X
b) Fuse
Only fit or replace a fuse when the device is unplugged from the mains.
Replace a blown fuse with a fuse of the same type and rating:
1. Unplug the device from the mains.
2. Unscrew the fuse holder at the back with an appropriate screwdriver.
3. Remove the old fuse and install a new one.
4. Replace the fuse holder and fasten it with the screwdriver.
Pull down in the arrow direction to tun on. The address switch shown on the diagram
is preset as "1".
230V AC 50 Hz
1500 W
11 Min.
24000Cuft/min.
2.5 Lt.
10 Kg
OK
OK
OK
OK
This symbol on the product or on its packaging indicates that this product
shall not be trated as household waste. Instead it shall be handed over to
the applicable collection point for the recycling of electrical an electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling
of this product. The recycling of amterials will help to conserve natural
resources. For more detailed information sabout recycling of this product,
please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
Rev. 1.10
EN