Multiplex Himax C 6310 Serie Manual De Instrucciones página 2

! These operating instructions are an integral part of this
product. They contain important information and safety notes,
and should be kept in a safe place at all times. Be sure to pass
them on to the new owner if you ever dispose of the product.
1. I
NTRODUCTION
Himax motors are manufactured to high standards for quality-
conscious modellers. Carefully optimised for low weight, high
efficiency, high torque and durability, Himax brushless motors are
the perfect choice as power plants for RC models.
2. S
PECIFICATION
Diameter:
Length:
Weight:
Max. output:
Max. rotational speed:
Max. case temperature:
Mounting:
Type:
#
RPM / V:
Cell count NiXX / LiPo:
Optimum working range:
Max. current for 15 sec.:
Hollow-shaft Ø:
The Himax C 6310 series of brushless motors are specially
designed for use in the MULTIPLEX FUNCOPTER with a maximum
all-up weight of about 1300 g.
3. S N
AFETY OTES
• Read the instructions before using the motor for the first time
• Check that the motor and the rotor blades are firmly attached
before every flight
• Do not connect the battery to the speed controller until you have
switched the RC system on, and checked that the throttle stick is
at the "OFF" position
• Never run the motor while holding it in your hand
• Do not exceed the stated maximum screw depth when installing
the motor
• Remove all loose, lightweight objects from the area below the
rotor blades before running the motor, as they may be sucked into
the rotor blades
• Protect the motor from dirt and damp
• Ensure that no foreign bodies get inside the motor
• When the motor is running, do not stand in line with the rotor
blades
• Do not exceed the maximum permitted rotational speed of the
motor and the rotor blades
• Stop the motor immediately if you notice vibration, and eliminate
the cause before running it again. You may need to balance the
rotor blades
•
Himax brushless motors must never be connected directly to a
power source, as this will wreck the motor
4. O N
PERATING OTES
Himax brushless motors must only be run in conjunction with a
sensorless controller for brushless motors. If the motor shaft spins in
the wrong direction, disconnect the battery (to avoid short-circuits)
and swap over any two of the leads between the motor and the
speed controller.
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten • www.multiplex-rc.de
Operating Instructions
Himax C 6310-xxxx – brushless outrunner motor
63 mm
32 mm
235 g
450 W
-1
10.000 Umin
o
65 C
∅ 30 mm / 4 x M4 (3 mm deep)
C 6310-0225 C 6310-0250
33 3070 33 3071
225 250
9 - 12 / 3S - 4S
15 A - 30 A 20 A - 35 A
40 A 48 A
4.0 mm
Do not bend the motor leads sharply. Deploy them in such a way
that they are not subjected from vibration and oscillation.
Do not shorten the wires attached to the motor. If you wish to use
different connectors, unsolder the existing ones.
Ensure that the motor and speed controller are adequately cooled
when running. The maximum motor load may only be used briefly,
i.e. no more than fifteen seconds. At the same time the maximum
case temperature of 65° C must not be exceeded.
Use properly balanced rotor blades only, as this avoids vibration and
premature bearing damage.
5. M N
AINTENANCE OTES
Brushless motors are largely maintenance-free, but a little care will
ensure that they last a very long time:
Protect the motor from dust and dirt - especially the ball races.
Soiled bearings may jam, and they will then need to be replaced.
For this reason lubricate the bearings with thin oil at regular
intervals. Do not immerse the motor in water or solvent.
6. G
UARANTEE
Our products are covered by the currently valid statutory guarantee
regulations. If you wish to make a claim under guarantee, please
contact the model shop where you purchased the product in the first
instance.
The guarantee does not cover faults and defects which are caused
by the following errors:
•
Improper operation (e.g. overheating), incorrect connections,
reversed polarity
•
Use of accessories other than genuine MULTIPLEX items
•
Accidental or deliberate damage
•
Faults due to normal wear and tear
•
Operating the motor outside the technical specification
•
Modifications / repairs which were not carried out by
MULTIPLEX or an authorised MULTIPLEX Service Centre
always use our official service for repairs
7. CE A
PPROVAL
This product has been assessed in accordance with the
relevant harmonised European directives. You are therefore
the owner of a product whose design fulfils the protective
aims of the European Community relating to the safe operation of
equipment.
You are entitled to see a copy of this Conformity Declaration. Please
contact MULTIPLEX Modellsport GmbH & Co.KG if you wish to do
this.
8. D I
ISPOSAL NFORMATION
Electrical equipment marked with the cancelled waste
bin symbol must not be discarded in the standard
household waste; instead it must be taken to a suitable
specialist disposal system.
In the countries of the EU (European Union) electrical equipment
must not be discarded via the normal domestic refuse system
(WEEE - Waste of Electrical and Electronic Equipment, directive
2002/96/EG). You can take unwanted equipment to your nearest
local authority waste collection point or recycling centre. There the
equipment will be disposed of correctly and at no cost to you.
By returning your unwanted equipment you can make an important
contribution to the protection of the environment.
Page 1/1