Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
PACKAGE CONTENTS
A – Flood Lamp
B –Fixture x4
Body x2
C– Electrical Plug x4
Assembly and Installation
1
Attaching and installing the flood light
WARNING: Never push the fixture into the ground by the flood lamp
body (A) or use a hammer to insert the ground stake (G) into the
ground.
Insert the fixture wire on the wire connector (E) into the groove located on
□
the top of the ground stake (G).
Ensure the fixture wire on the wire connector (E) stays in the center of the
□
groove to avoid damage to the fixture wire. Screw the flood lamp body (A)
onto the ground stake (G).
Prepare a hole in the installation location. Use a tool such as a screwdriver
□
(not included) to prepare the installation hole to ensure that the hole is not
larger than the ground stake (G).
Install the fixture in the ground by pushing on the foot step (1) on the ground
□
stake (G). Do not push on the flood lamp body (A).
The flood lamp body (A) can rotate up and down 160 degrees.
□
D –Electrical Slot Connector x4
E – Wire Connector x6
2
Attaching and installing the path light
Insert the electrical plug (C) into the electrical slot connector (D).
□
Insert the fixture (B) into the post (F).
□
Insert the fixture wire on the wire connector (E) into the groove located
□
on the top of the ground stake (G).
Screw the ground stake (G) into the post (F). Ensure the fixture wire
□
on the wire connector (E) stays in the center of the groove of the
ground stake (G) to avoid damage to the fixture wire.
Prepare a hole in the installation location. Use a tool such as a
□
screwdriver (not included) to prepare the installation hole to ensure
that the hole is not larger than the ground stake (G).
Install the fixture in the ground by pushing on the foot step (1) on the
□
ground stake (G). Do not push on the fixture (B).
1
Use and Care Guide
LED LOW VOLTAGE LIGHT 6PK KIT
2 FLOOD LIGHTS, 4 PATH LIGHTS
F – Post
(17.323in.) x4
WARNING: Never push the fixture into the ground by the fixture (B) or
use a hammer to insert the ground stake (G) into the ground.
Item #1001 488 938
Model #IWW6626L
G - Ground Stake
(6.693 in.) x6
Publicidad
Tabla de contenido
Solución de problemas
Manuales relacionados para HAMPTON BAY IWW6626L
Resumen de contenidos para HAMPTON BAY IWW6626L
- Página 1 Item #1001 488 938 Model #IWW6626L Use and Care Guide LED LOW VOLTAGE LIGHT 6PK KIT 2 FLOOD LIGHTS, 4 PATH LIGHTS PACKAGE CONTENTS A – Flood Lamp B –Fixture x4 D –Electrical Slot Connector x4 F – Post G - Ground Stake Body x2 C–...
- Página 2 Assembly and Installation (continued) Connecting the wires WARNING: The wire connector (E) contacts have sharp edges for piercing the main low voltage cable. To avoid injury, do not touch the metal contacts. CAUTION: The wire from the low voltage power unit should be 12-16 AWG type underground Low Energy Circuit Cable.
-
Página 3: Care And Cleaning
Care and Cleaning □ □ Clean the fixture with a soft dry cloth. Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible Cause Solution The fixture will not □ □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. There is no power. -
Página 4: Montaje E Instalación
Artículo #1001 488 938 Modelo #IWW6626L GUÍA DE USO Y MANTENIMIENTO REFLECTOR LED DE BAJO VOLTAJE EQUIPO DE 6 PAQUETES 2 LUCES DE INUNDACION, 4 LUCES PATH PACKAGE CONTENTS A – Cuerpo del Reflector B – Estructura de la Lampara x4 D –... -
Página 5: Conexión De Los Cables
Montaje e Instalación (continuación) Conexión de los cables ADVERTENCIA: Los contactos del cable conector (E) tienen bordes filosos para atravesar el cable principal de bajo voltaje. No toque los contactos de metal para evitar lesiones. PRECAUCIÓN: El cable de la unidad de bajo voltaje debe ser un cable subterráneo de circuito de baja corriente tipo 12-16 AWG. -
Página 6: Mantenimiento Y Limpieza
Mantenimiento y Limpieza □ □ Limpia la lámpara con un paño suave y seco. No uses limpiadores con químicos, solvents, o productos abrasivos. Solución de Problemas Problema Causa Posible Solución El accesorio no □ □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito GFC. No hay corriente. -
Página 7: Fcc Warning
FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.