Steren CCTV-490 Manual De Instrucciones

Before using your new 4-camera CCTV power supply, please
read this instruction manual to prevent any damage. Put it away
in a safe place for future referen
HIGHLIGHTS
The CCTV camera power supply delivers a constant and regulated 12V
output to feed 4 closed-circuit cameras.
The metallic chassis makes it discreet and professional power source with
lock, it has a general power indicator light and independent fuse protection
that prevents overload or short circuit in the cameras, as well as a general
on / off switch and all necessary installation fittings.
• 16.5 x 16 x 4.7cm
• 4 outputs.
• Overload and short circuit protection.
MOUNTING
Fix the power supply using included screws and wall plugs.
1. Select the mounting location and make a
hole for the wall plugs.
2. Place the wall plugs and screws to hang up
the box. Do not tighten the screws completely.
3 Hang the box up on the screws. If you
require fixing it more firmly, place the two
additional screws.
CONNECTION
BLACK (V-)
RED (V+)
3. Connect one end of the power cord
to the source of power, connecting the
"live" cable to screw marked L, neutral
to the one marked N and the ground to
[ ]. The other end of the cable must
be connected to the electric current.
Once the connections are made,
switch to on.
The corresponding LEDs to the
connected cameras should light.
1 Pass cameras power cables through
the holes located at the top of the power
supply's frame.
2. For each power cord, connect the
red wire to positive (+) and the black
cable to the corresponding negative (-)
screws.
USE
To avoid cameras disconnection,
use the lock located at the
power supply lid.
TROUBLESHOOTING
TROUBLE
Check connections.
A camera
Make sure the power outlet to which the power supply is
does not
connected is energized.
receive power
Check, and if necessary, change the fuse for the
camera that does not receive power.
Check connections.
Make sure the cable to which the power supply is
The source
connected is energized.
does not light
Check and if necessary, change the main fuse of the
power source.
SPECIFICATIONS
Input: 110-220V~ 60/50Hz 50Wmax
Output: 12V - - - 3A (x 4)
Nominal consumption: 36 kWh/month
Stand-by power consumption: 17.52 kWh/year
Before using your new Electronic insect killer, please read this
Product design and specifications are subject to change
instruction manual to prevent any damage. Put it away in a
without previous notice.
Product: 4-camera CCTV power supply
Part number: CCTV-490
Brand: Steren
This Steren product is warranted under normal usage against defects in
workmanship and materials to the original purchaser for one year from the
date of purchase.
CONDITIONS
1.- This warranty card with all the required information, invoice or purchase
ticket, product box or package, and product, must be presented when
warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free
of charge.
3.- The repairing time will not exceed 30 natural days, from the day the
claim was received.
4.- Steren sell parts, components, consumables and accessories to
customer, as well as warranty service, at any of the addresses mentioned
later.
THIS WARRANTY IS VOID IN THE NEXT CASES:
If the product has been damaged by an accident, acts of God, mishandling,
leaky batteries, failure to follow enclosed instructions, improper repair by
unauthorized personnel, improper safe keeping, among others.
a) The consumer can also claim the warranty service in the purchase
establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice
or purchase ticket.
RETAILER INFORMATION
Name of the retailer
Address
Product
Brand
Part number
Serial number
Date of delivery
In case your product fails or have questions, please contact your
nearest dealer. If you are in Mexico, please give a call to our Call
Center. Call Center
01 800 500 9000
SOLUTION
WARRANTY