Descargar Imprimir esta página

Stanley Super 180 TIG Lift Manual De Usuario página 4

Publicidad

The product is a portable, lightweight, single-phase 230 V,
50/60Hz welder with inverter technology. It allows MMA welding
with all electrodes type. The model allows TIG welding of the
most metals except the aluminium and alloys. Can be connected
to power generators with power equal to or higher than that
reported in Table 2. It is equipped with "HOT START", "ARC
FORCE" and "ANTI STICK" functions (for more details please
refer to the GENERAL PART manual included in the package).
DESCRIPTION OF THE MACHINE
Fig 1
1.
Welding current Knob
2.
Negative socket(-)
3.
Positive socket (+)
4.
Thermal protection LED indicator
5.
LED indicator power on
6.
selector TIG-MMA (only for the model TIG)
7.
ON-OFF switch
8.
Power Cord
INSTALLATION
The installation must be made by trained personnel in compliance
to the standard IEC 60974-9 and the current and local legislation.
To lift the machine it must be used the handle positioned on top of
the product with the machine in OFF position. The input voltage
must match the voltage indicated on the technical plate located on
the product. Use the machine on electric system having supply
features and power protection (fuse and / or differential switch)
that are compatible with the current required for its use. For more
details see the information on the plate placed on the machine.
TURN ON
Warning: Use all precautions required in the safety general
manual before operating the welder, reading carefully the risks
associated with the welding process.
MAINTENANCE
Refer all servicing to qualified personnel.
Anomalies
MMA
The device does not deliver any current
and the yellow indicator LED of thermal
protection lights up.
The device is on but it does not
deliver any current.
Your unit does not weld correctly.
TIG
Instable arc
The electrode melts
This Model is without PFC device and do not comply with IEC 61000-3-12. If they are to be connected to a low-voltage
mains supply, it is the responsibility of the user to ensure they can be connected. If necessary consult the operator of
your electrical
distribution system
This welding machine is for professional use only and is reserved for the industry.
ENGLISH
Causes
Remedies
Wait for the end of the cooling
The welder thermal
time, around 2 minutes. The
protection has turned on.
indicator led turns off.
The cable of the earth
clamp or electrode holder
Turn off the machine and check the connections.
is not connected to the
welder.
. Check the polarity advised on the
Polarity error
electrodes packaging.
-)Default coming from the
-) Use a tungsten electrode with the
tungsten electrode
adequate size
-)Too important gas flow
-) Reduce gas flow rate
rate
Check that the earth clamp is really
Polarity error
connected to +
ELECTRODE WELDING (MMA)
1. Connect the connectors of the earth clamp and electrode
holder to the poles of the device; choose the polarity
(forward or reverse) depending on the coating of the
electrodes (for more information see the information on
the electrodes packaging).
2. Connect the earth clamp to the work piece and insert the
electrode in the electrode holder
3. Connect the power cord to the power supply and turn on
the welder
4. Select the welding current as a function of the type of
electrode selected (Tab. 1).
5. Start the welding operation using all the necessary
protections to security.
Note: You must disconnect the earth clamp to the metal work
piece just after switching off the welding machine.
TIG WELDING (only for the TIG type)
1.
Connect the connectors of the earth clamp and of the
torch to the poles of the device; choose the polarity (forward or
reverse) in relation to the type of material to be welded
2.
Connect the earth clamp to the work piece
3.
Connect the torch gas tube to the gas cylinder
4.
Select the TIG mode
5.
Select the welding current
6.
Select the gas flow of the gas cylinder and open the torch
valve
7.
Connect the power cord to the power supply and turn on
the welder
8.
Use the torch to weld as in the following without a puse
between the two phases
Stopped the welding, turn off the machine and close the gas valve.
THERMAL PROTECTION
In case of overheating of the machine the yellow LED indicates
that the thermal protection is on, you can start to weld it when the
LED is off
Touch the piece with the electrode
Lift the electrode from the piece
about 2-5 mm

Publicidad

loading