Indicators And Controls - Jensen PS260 Manual De Instalación Y Operación

PS260 / PS285 / PS2130 / PS2180

Indicators and Controls

Power Indicator
The power indicator provides a visual indication that the amplifier is turned on.
Level
The input level control matches the output of your radio to the input of the amplifier. After the
installation is complete, make sure the input level control on the amplifier is turned down all the way
(counterclockwise or all the way to the left). Play a tape or CD (make sure bass and treble settings or
EQ are flat) and turn the volume up slowly until you just start to hear distortion. Back the volume down
just a bit. On the amplifier, slowly turn up the input level control (clockwise or to the right) until you just
start to hear distortion, and back it down a bit. Now the radio and amplifier levels are matched.
Bass Boost
The Bass Boost is continuously adjustable from 0 to +18dB @ 45Hz. Adjusting the Bass Boost level
allows different subwoofer/enclosure combinations to be equalized. Use this control to increase the
level of low bass available from your subwoofer/enclosure combination. Ported and Band Pass
enclosures should be limited to about +6db to +9dB of boost. Sealed enclosures should be able to
accept the full +18dB of boost, if necessary. The full +18dB of boost should be reserved for special
applications because misuse of the Bass Boost could damage your subwoofers at high volumes.
Crossover
The PS series amplifiers have built-in low-pass and high-pass crossover filters for bi-amplifying the
system. Adjust the crossover to accommodate your chosen installation method. Select LPF (low pass
filter) when the amplifier will be driving woofers or subwoofers. Choose FULL when crossover mode
is not active and the amplifier is in "full range" mode. Select HPF (high pass filter) when the amplifier
will be driving full range/separate speakers, and you want to limit the "bass" going to these speakers.
L-CHX / R-CHX
These controls adjust the crossover point from 40Hz to 400Hz. Typical crossover is between 60Hz
and 80Hz. Dual cone, two-way and three-way speakers will typically be smaller in size than sub-
woofers, and the bass going to these speakers will need to be attenuated. Typical high pass
crossover is between 100Hz to 240Hz. Since musical tastes vary, use the above settings as a starting
point and adjust the crossover by ear while listening to the music of your choice. Be sure to set the
head unit tone controls to flat before adjusting crossover.
Remote Port
The remote port operates an optional Remote Bass Control (PS1-RMT) and allows adjustment of the
input level of the PS2130 or PS2180 from a dash-mounted control. When installing subwoofers in a
vehicle, it is often convenient to adjust the "bass volume" depending on musical selection.
Protect Indicator
The protect indicator provides a visual indication that a problem exists and the protection circuitry has
protected the amplifier by shutting it down. Turn the system off and correct the problem before turning
the system on.
Thermal Protection
The amplifier will shut down if its termperature exceeds a safe operating level. The amplifier will
remain off until it cools to a safe operating temperature. Exercise care, as the exterior of the amplifier
may get uncomfortably hot to the touch before shutting down.
Overload and Short Circuit Protection
The amplifier will shut down if a short circuit condition exists or if electical current demands exceed
safe levels.
Testing
Before you finish the installation, you should perform the following tests to make sure the wiring is
correct and everything is operating properly.
Reconnect Battery
When wiring is complete, reconnect the battery negative terminal.
Test Power Wiring
Turn on the receiver, but do not turn up the volume. The amplifier power light should come on. If not,
check the REM and +12V wires. Turn up the receiver volume slightly. All speakers should operate. If
not, check wiring connections at amplifier and speakers.
Test Speaker Connections
These tests make sure the speakers are connected properly. If speakers don't play at all, one (or
both) speaker wires may be disconnected.
PS260
PS285
Level
Nivel de entrada
Niveau
Power Indicator
Indicador de energía
Bass Boost
Indicateur de puissance
Bajos
Bas
PS2130
PS2180
Level
Nivel de entrada
Niveau
Power Indicator
Indicador de energía
Bass Boost
Indicateur de puissance
Bajos
Bas
9
Indicators and Controls)
Indicadores y Controles
Indicateurs et Contrôles
L-CHX
180 180
R-CHX
80 80 300 300
Hz Hz
1.4
180
.5
4 80 300
Hz Hz
1.4 180 180
180
4 5 2 80 80 300 300 80 300
Hz Hz Hz Hz
Crossover
Cruce
2
Filtrage
L-CHX
Remote Control (optional)
Control remoto (opcional)
180 180
R-CHX
Prêt à être télécommandé (acultative)
80 80 300 300
Hz Hz
1.4
180
4 .5
80 300
Hz Hz
1.4 180 180 180
80 300
4 5 2 80 80 300 300
Hz Hz Hz Hz
Crossover
Cruce
2
Filtrage
Protect Indicator
Indicador de la protección
Indicateur de la protection
Protect Indicator
Indicador de la protección
Indicateur de la protection