Troubleshooting Guide; Supplied Accessories - Sylvania SST4324S Manual Del Usuario

OPERATIONS (Continued)
Programming may be rated by the Motion Picture Association of America (MPAA) or accord-
●
ing to the Television Parental Guidelines. In order to block any inappropriate programming, set
your limits in both places (MPAA RATING and TV RATING).
You cannot access the menu when the "PROTECTED PROGRAM by ..." message appears. In
●
this case, change to an unblocked channel, then press the MENU button.
[MPAA RATING SET UP]
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel) ▲ or ▼ button to point to "V-CHIP SET UP", then
press the VOL(ume) ▲ button.
3) Use the number buttons to enter 4-digit access code. The default access
code is 0000. If you have not set up your personal access code, you should
use 0000.
4) Press the CH(annel) ▲ or ▼ button to point to "MPAA RATING", then
press the VOL(ume) ▲ button.
5) Press the CH(annel) ▲ or ▼ button to point to your desired item, then
press the VOL(ume) ▲ button to select [BLOCK] or [VIEW].
<Selection> <Rating Category Explanations>
• G: General Audience
• PG: Parental Guidance suggested.
• PG-13: Unsuitable for children under 13
• R: Restricted; under 17 requires accompanying parent or
adult guardian
• NC-17: No one under 17 admitted
• X: Mature audience only
When you select the rating category and set it to [BLOCK], the higher rat-
●
ing will change to [BLOCK] automatically. Also, the lower rating will
change to [VIEW] automatically.
When you set "G" to [BLOCK] or [VIEW], then all ratings will change to
●
[BLOCK] or [VIEW] automatically.
When you set "X" to [VIEW], then all ratings will change to [VIEW]
●
automatically.
6) Press the MENU button to exit the menu.
[TV RATING SET UP]
1) Press the MENU button so that the menu display appears on the TV screen.
2) Press the CH(annel) ▲ or ▼ button to point to "V-CHIP SET UP", then
press the VOL(ume) ▲ button.
3) Use the number buttons to enter 4-digit access code. The default access
code is 0000. If you have not set up your personal access code, you should
use 0000.
4) Press the CH(annel) ▲ or ▼ button to point to "TV RATING", then press
the VOL(ume) ▲ button.
5) Press the CH(annel) ▲ or ▼ button to point to your desired item, then
press the VOL(ume) ▲ button to select [BLOCK] or [VIEW].
<Selection> <Rating Category Explanations>
• TV-Y: Appropriate for all children
• TV-Y7: Appropriate for children seven and older
• TV-G: General Audience
• TV-PG: Parental Guidance suggested
• TV-14: Unsuitable for children under 14
• TV-MA: Mature audience only

TROUBLESHOOTING GUIDE

Sometimes a performance problem can be easily solved by checking seemingly apparent but often over-
looked possibilities. Before arranging for service, check these items. It could save you time and money.
QUICK SERVICE CHECK LIST
POSSIBLE REMEDY
Try a new channel, if OK, then possible station trouble.
Is TV plugged in?
Power at outlet?
Is TV's POWER button on?
Is antenna connected to terminal on the back of the set?
If outside antenna is being used, check for broken wire.
Check for local interference.
Turn off with POWER button and then turn it on after about a minute.
Adjust COLOR control.
Adjust CONTRAST & BRIGHT control.
Check batteries in Remote Control.
Move the TV away from the nearby speakers and appliances which generate a
magnetic field.
Turn off using the POWER button, then turn it on again 30 minutes later or so.
Closed Caption Problem
My TV is showing captions that are
misspelled.
My TV will not show the text in its entirety
or there is a delay of what is being said.
My captions are scrambled with white
boxes on the TV screen.
My program guide listed a TV show as
being closed captioned
but none of the captions were displayed.
My prerecorded videotape does not show
any captions. The tape box mentions it
being closed captioned.
My TV screen shows a black box on certain
channels.
As an E S ® Partner, our company has determined that this product meets
NERGY TAR
the E S ® guidelines for energy efficiency. E
NERGY TAR
Possible Remedy
You are watching a live broadcast and spelling errors made by the
closed captioning production company may pass through uncorrect-
ed. A prerecorded program will not show any misspelled words
because of the normal time available for editing the captions.
Captions that are delayed a few seconds behind the actual dialogue
are common for live broadcasts. Most captioning production compa-
nies can display a dialogue to a maximum of 220 words per minute.
If a dialogue exceeds that rate, selective editing is used to insure that
the captions remain up-to-date with the current TV screen dialogue.
Interference caused by building, power lines, thunderstorms, etc.
may cause scrambled or incomplete captions to appear.
Broadcasters may at times use a time compression process to the
actual program so that additional advertising time can be given.
Since the decoder cannot read the compressed information, captions
will be lost.
The videotape was either an illegal copy or the tape duplicating
company accidentally left out the captioning signals during the
copying process.
You are in the TEXT mode. Select CAPTION mode or CAPTION
[OFF].
S ® is a U.S. registered mark.
NERGY TAR
When you select the rating category and set it to [BLOCK], the higher rat-
●
ing will change to [BLOCK] automatically. Also, the lower rating will
change to [VIEW] automatically.
When you set "TV-Y" to [BLOCK] or [VIEW], then all ratings will
●
change to [BLOCK] or [VIEW] automatically.
When you set "TV-MA" to [VIEW], then all ratings will change to
●
[VIEW] automatically.
PICTURE
[V-CHIP SET UP SUB RATINGS]
CHANNEL SET
[ENGLISH] ESPAÑOL
When you select TV-Y7, TV-PG, TV-14, or TV-MA and you press the
V-CHIP SET UP
VOL(ume) ▲ button, the sub-ratings will appear on the TV screen.
CAPTION [OFF]
If you select the rating category (example: TV-PG) and set it to [BLOCK]
TV SOUND [MAIN]
or [VIEW], the sub-ratings (example: V for Violence) will change to
[BLOCK] or [VIEW] automatically.
ACCESS CODE
You can set the sub-ratings to [BLOCK] or [VIEW] individually when the
_ _ _ _
rating category is set to [BLOCK]. To set the sub-ratings individually, fol-
low the steps below.
When you select [TV-Y7]:
●
Press the CH(annel) ▲ or ▼ button to select "FV" (Fantasy Violence).
Then, press the VOL(ume) ▲ button to select [BLOCK] or [VIEW].
TV RATING
When you select [TV-PG], [TV-14] or [TV-MA]:
MPAA RATING
●
Press the CH(annel) ▲ or ▼ button to select "D" (Suggestive Dialog),
CHANGE CODE
"L"(Coarse Language), "S"(Sexual Situation), or "V" (Violence). Then,
press the VOL(ume) ▲ button to select [BLOCK] or [VIEW].
Notes:
G [VIEW]
When you select [TV-MA], "D" does not appear on the TV screen.
●
PG [VIEW]
The sub-ratings set to [BLOCK] appear next to the rating category in the
●
PG-13 [VIEW]
TV RATING menu.
R [VIEW]
NC-17 [VIEW]
6) Press the MENU button to exit the menu.
X [VIEW]
[V-CHIP ACCESS CODE]
To change access code, follow steps.
1) Press the MENU button, then press the CH(annel) ▲ or ▼ button to select
V-CHIP SET UP. Press the VOL(ume) ▲ button to continue.
2) Press the number buttons to enter your old access code. If you have never
PICTURE set up your personal access code, use 0000.
CHANNEL SET 3) Press the CH(annel) ▲ or ▼ button to select "CHANGE CODE", then
[ENGLISH] ESPAÑOL
press the VOL(ume) ▲ button to continue.
V-CHIP SET UP
CAPTION [OFF] 4) Use the number buttons to enter your desired access code in the NEW
TV SOUND [MAIN]
CODE space. Then, enter the same code in the CONFIRM CODE space.
Your new access code is set. You will return to the "V-CHIP SET UP".
ACCESS CODE
If the code in the CONFIRM CODE space does not match the code in the
_ _ _ _
NEW CODE space, repeat step 4, making sure you enter the same new
code exactly in the CONFIRM CODE space.
Notes:
• If a power failure occurs, the default code, 0000 will be the access code.
• If you connect the power cord to an AC outlet that is controlled by a wall
switch, your personal access code will be erased every time you turn off the
TV RATING
power at the wall switch. The default code will return to 0000.
MPAA RATING
CHANGE CODE
[IF YOU FORGET YOUR ACCESS CODE]
You should restore the access code to 0000 as your access code, unplug the
TV's power cord for 10 seconds, then plug it in again.
MAINTENANCE
CABINET CLEANING
Wipe the front panel and other exterior sur-
●
faces of the TV with a soft cloth immersed
in lukewarm water and wrung dry.
Never use a solvent or alcohol. Do not spray
●
insecticide liquid near the TV. Such chemi-
cals may cause damage and discoloration to
the exposed surfaces.

SUPPLIED ACCESSORIES

Remote control unit
(NE139UD)
Batteries ("AA" x 2)
SPECIFICATIONS
GENERAL SPECIFICATIONS
Television system:
Closed Caption
System:
Channel coverage
VHF:
UHF:
CATV:
Tuning System
Channel access:
Terminals
Antenna input:
S-Video input:
Video input:
Audio out/input:
Stereo Sound System
2 speakers
PICTURE TUBE CLEANING
Wipe the picture tube of the TV with a soft
cloth. Before cleaning the picture tube, discon-
nect the power cord.
Owner's Manual
(1EMN20207)
ELECTRICAL SPECIFICATIONS
NTSC-M Sound output:
TV Standard
§15.119/FCC
OTHER SPECIFICATIONS
Remote control:
2 ~ 13
14 ~ 69
Operating
2 ~ 13, A ~ W,
temperature:
W+1 ~ W+84,
A-5 ~ A-1, 5A
Power requirements: AC120V, 60Hz
181 channel
Power consumption
frequency synthesized
(Maximum):
tuning system
Picture tube:
Direct access keyboard,
Dimensions:
programmable
scan and up/down
Weight:
VHF/UHF/CATV
75 ohm unbalanced
(F-type)
Mini DIN 4-pin jack
•Designs and specifications are subject to
RCA connector x 2
change without notice and without our
RCA connector x 6
legal obligation.
•If there is a discrepancy between languages,
the default language will be English.
TV-Y [VIEW]
TV-Y7 ( ) [VIEW]
TV-G [VIEW]
TV-PG ( ) [VIEW]
TV-14 ( ) [VIEW]
TV-MA ( ) [VIEW]
TV-Y7 [BLOCK]
FV [BLOCK]
TV-PG [BLOCK]
D [BLOCK]
L [BLOCK]
S [BLOCK]
V [BLOCK]
TV-Y [VIEW]
TV-Y7 ( ) [VIEW]
TV-G [BLOCK]
TV-PG (DLSV) [BLOCK]
TV-14 (DLSV) [BLOCK]
TV-MA ( LSV) [BLOCK]
PICTURE
CHANNEL SET
[ENGLISH] ESPAÑOL
V-CHIP SET UP
CAPTION [OFF]
TV SOUND [MAIN]
ACCESS CODE
_ _ _ _
TV RATING
MPAA RATING
CHANGE CODE
NEW CODE
_ _ _ _
COMFIRM CODE
_ _ _ _
Owner's
Manual
2W, 8 ohm x2
Digital encoded
infrared light system
5°C to 40°C
(41°F~104°F)
134W
32"
H : 26-3/8" (671mm)
W: 29-15/16" (760mm)
D : 21-1/4" (540mm)
112.6 lbs. (51kg)