Descargar Imprimir esta página
GE WD35X10047 Instrucciones De Instalación
GE WD35X10047 Instrucciones De Instalación

GE WD35X10047 Instrucciones De Instalación

Juego de reemplazo del panel de puerta

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Installation
Instructions
BEFORE YOU BEGIN
STOP
Read these instructions completely
and carefully.
IMPORTANT
tions for local inspector's use.
IMPORTANT
codes and ordinances.
Note to Installer – Be sure to leave these
instructions with the Consumer.
Note to Consumer – Keep these instructions
with your Owner's Manual for future
reference.
WARNING:
To prevent electric shock, disconnect electri-
cal power supply to dishwasher before
changing panels. Do not operate dishwasher
while changing panel.
CAUTION:
On new installations, do not remove wood
base until you are ready to install the dish-
washer. The dishwasher will tip over when
the door is opened.
TOOLS AND MATERIALS REQUIRED:
• Gloves to protect against sharp edges
• Stubby Phillips screwdriver
These panel kits provide for the installation of
a replacement door panel.
KIT INCLUDES:
• Door panel
– Save these instruc-
– Observe all governing
Door Panel Replacement Kit
WD35X10047/GPF810B/WD31X10050 - BLACK
WD35X10048/GPF810C/WD31X10051 - BISQUE
WD35X10049/GPF810S/WD31X10059 - STAINLESS
WD35X10050/GPF810W/WD31X10052 -WHITE
1 REMOVE DOOR PANEL
Figure 1
• Open dishwasher door.
• Remove the 10 Phillips head screws (Figure
1) holding the inner door to the outer panel.
Retain screws.
• Close dishwasher door.
• Remove the two screws on the bottom of
the door panel (Figure 2). Retain screws.
• Rotate the bottom of the outer door panel
outwards (Figure 3). The bottom of the panel
should be in front of the hinge arms.
• Lift the panel up and over the corner cutouts
in the escutcheon until the panel is sepa-
rated from the inner door. If the dishwasher
is installed in a cabinet, open the door
slightly to remove the panel.
• Close door.
Escutcheon
Bottom
Phillips Screws
Figure 2
Figure 3

Publicidad

loading

Resumen de contenidos para GE WD35X10047

  • Página 1 Door Panel Replacement Kit Installation WD35X10047/GPF810B/WD31X10050 - BLACK WD35X10048/GPF810C/WD31X10051 - BISQUE Instructions WD35X10049/GPF810S/WD31X10059 - STAINLESS WD35X10050/GPF810W/WD31X10052 -WHITE 1 REMOVE DOOR PANEL BEFORE YOU BEGIN STOP Read these instructions completely and carefully. IMPORTANT – Save these instruc- tions for local inspector’s use.
  • Página 2 2 INSTALL NEW PANEL Escutcheon Escutcheon Opening Check Fit Around Escutcheon Escutcheon Ribs Bottom Phillips Screws Figure 5 Figure 6 Figure 4 • If the dishwasher is installed in a cabinet • Loosely install the 2 original screws at the open the door slightly to install the panel.
  • Página 3 Juego de reemplazo del panel Instrucciones de puerta WD35X10047/GPF810B/WD31X10050 - NEGRO de instalación WD35X10048/GPF810C/WD31X10051 - ESMALTADO WD35X10049/GPF810S/WD31X10059 - INOXIDABLE WD35X10050/GPF810W/WD31X10052 – BLANCO ANTES DE COMENZAR 1 RETIRE EL PANEL DE PUERTA PARE Lea cuidadosamente todas estas instrucciones. IMPORTANTE: Conserve estas instrucciones para uso del inspector local.
  • Página 4 2 INSTALE EL PANEL NUEVO Abertura Lámina de la lámina Verifique la posición alrededor de la lámina Costillas de la lámina Tornillos Phillips inferiores Figura 5 Figura 6 Figura 4 • Si el lavavajillas está instalado en un armario, • Atornille, sin apretar, los 2 tornillos originales abra ligeramente la puerta para instalar el en la parte inferior del panel (Figura 6).

Este manual también es adecuado para:

Gpf810bWd31x10050Wd35x10048Gpf810cWd31x10051Wd35x10049 ... Mostrar todo