Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

Model 9460
Four head Power Supply
for the
Remote Strobe Systems
WARNING!
Failure to install or use this product according to manufacturers recommendations may result in property damage,
serious bodily/personal injury, and/or death to you and those you are seeking to protect!
Do not install and/or operate this safety product unless you have read and understand the
safety information contained in this manual.
1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are
essential to ensure the safety of you and those you are trying to protect.
2. Exercise caution when working with live electrical connections.
3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high
current arcing, which can cause personal injury and/or severe vehicle damage, including fire.
4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output
performance of the system is maximized and the controls are placed within convenient reach of the operator so that s/he
can operate the system without losing eye contact with the roadway.
5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In use, the
vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks
or compartment doors), people, vehicles, or other obstructions.
6. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.
Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an
intersection, driving against traffic, responding at a high rate of speed, walking on or around traffic lanes.
7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying
all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal laws and
regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.
Introduction:
The 9460 Four Head Power supply is designed to work with
any of ECCO's 9000 Series Remote Strobe Heads. The ad-
vanced features include:
Meets SAE J1318 Class 2
Sealed, weatherproof connectors
Epoxy-filled for rugged environments
Dual and Quad selectable flash modes
High and Medium selectable intensity modes
Output short-circuit protection
920-9460-00 Rev. C
Installation and Operation Instructions
Specifications:
Size:
Weight:
Input voltage:
Input current:
Input watts:
Flash rate:
(Each outlet)
Output power:
(Each Strobe
channel)
Temp range:
6.4 x 7.2 x 1.9 inches high
4.3 lbs
12/24 VDC systems
6.6 A average (12V)
2.8 A average (24V)
100 W maximum
120 cycles/min (Quad mode)
140 cycles/min (Dual mode)
Alternating Pairs: channels 1/2 and 3/4
15 joules (Quad High)
11 joules (Quad Medium)
13 joules (Dual High)
7 joules (Dual Medium)
-30° C to +50° C
Page 1 of 3

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Ecco 9460

  • Página 1 The manufacturer assumes no liability for any loss resulting from the use of this warning device. Specifications: Introduction: Size: 6.4 x 7.2 x 1.9 inches high The 9460 Four Head Power supply is designed to work with Weight: 4.3 lbs any of ECCO’s 9000 Series Remote Strobe Heads. The ad- Input voltage:...
  • Página 2 If damage is found, or parts are When drilling into any vehicle surface, make sure that the area is free missing, contact the transit company or ECCO. Do not use from any electrical wires, fuel lines, vehicle upholstery,etc. that could damaged or broken parts.
  • Página 3 833 West Diamond St Boise, Idaho 83705 Customer Service USA 800-635-5900 UK +44 (0)113 237 5340 AUS +61 (0)3 63322444 ECCO © 2006 www.eccogroup.com 920-9460-00 Rev. C Page 3 of 3...
  • Página 4: Introducción

    El fabricante no asume responsabilidad por la pérdida que resulte del uso de este dispositivo de advertencia. Especificaciones: Introducción: Tamaño: 16,2 (6,4) x 18,2 (7,2) x 4,8 (1,9) cm (pulg) de alto La fuente de alimentación para cuatro cabezales 9460 está Peso: 2 kg. (4,3 libras) diseñada para trabajar con cualquier cabezal estroboscópico Tensión de entrada: sistemas de 12 a 24 V CC remoto de la serie 9000 de ECCO.
  • Página 5: Instalación Y Montaje

    Importante: Si solo se utilizan 3 cabezales y están diseñados para aceptar los cables remotos de ECCO. Estos estroboscópicos, instale el enchufe sin conexión en el cables son de 15 pies (4,5 m), 35 pies (10 m) y 50 pies (15 m) de largo tomacorrientes sin uso.
  • Página 6: Descripción

    833 West Diamond St. ECCO © 2006 Boise, Idaho 83705 Servicio al cliente EE.UU. 800.635.5900 Reino Unido +44 (0)113 237 5340 AUS +61 (0)3 63322444 www.eccogroup.com 920-9460-00 Rev. C Página 3 de 3...
  • Página 7: Caractéristiques Techniques

    Caractéristiques techniques : Introduction : Dimensions : 6,4 x 7,2 x 1,9 po. de haut L’alimentation 9460 à quatre têtes est conçue pour fonctionner Poids : 4,3 lb. avec n’importe quelle tête stroboscopique à distance de la série Tension d’entrée : Systèmes de 12 à...
  • Página 8 Important : Si vous n’utilisez que 3 têtes stroboscopiques, sont conçus pour recevoir des câbles à distance ECCO. Ces câbles installez la fiche vierge dans la prise non utilisée. Cette fiche font 15 pi., 35 pi. et 50 pi. de long et ils existent aussi en versions est livrée avec l’unité.
  • Página 9 Certains États n’autorisent pas l’exclusion ou la limitation de dommages indirects ou accessoires. 833 West Diamond St Boise, Idaho 83705 Customer Service États-Unis 800.635.5900 Royaume-Uni +44 (0)113 237 5340 AUS +61 (0)3 63322444 ECCO © 2006 www.eccogroup.com 920-9460-00 Rév. C Page 3 sur 3...

Tabla de contenido