Before You Start; Tools Required - Evenflo WALK-THRU Guia De Inicio Rapido

To prevent serious injury or death, securely install gate and use according to manufacturer's
instructions and warnings.
• NEVER use with a child able to climb over, dislodge or open the gate.
• NEVER leave child unattended.
• Intended for use ONLY with children from 6 – 24 months.
• Use ONLY on openings between 28" (71 cm) and 42" (106 cm) wide.
• Gate MUST ALWAYS swing away from stairs.
• ALWAYS keep gate securely locked in a closed position. Remove gate from opening when not in use.
• Use ONLY with locking mechanism securely engaged.
• DO NOT step over gate.
• STOP using gate if any parts are missing or become damaged.
• Periodically check all fasteners to be sure they are tight and secure.
• This gate will NOT necessarily prevent all accidents.
• When installing against drywall, make sure mounting surface is reinforced with a wall stud.
• PET STRANGULATION HAZARD – Pets can force themselves into very small openings. Use this gate only with pets whose
head or body WILL NOT fit into openings in the gate, between the gate and the floor, or between the
Latch Mechanism
Latch Housings
An electric drill with 1/8" drill bit, Phillips screwdriver, pencil, and adhesive tape.
Use a handheld Phillips screwdriver when installing screws.
NOTE: If you are missing parts, visit us at www.evenflo.com or call
ParentLink at 1-800-233-5921.
• Visit us at: www.evenflo.com • USA: 1-800-233-5921, 8 AM – 5 PM EST
• Canada: 1-937-773-3971 • México: 01-800-706-12-00
WARNING
gate and the wall.
Hinge Brackets
Contents of Hardware Bag:
Gate Panels
(8) Long Hinge Screws
(1) Paper Mounting Template
(2) Hinge Plates
(2) Latch Housings
(1) Swing Stop
(2) #10 x 1/2" Screws

Tools Required

IMPORTANT: You can use this gate at the top or bottom of stairs ONLY if:
• The gate is mounted over the floor at the top or bottom of a stairwell.
• The gate is mounted into a solid wood structure, e.g. wooden doorway jamb, solid wood banister post,
or wall stud behind sheet rock.
• The gate is installed according to these instructions, using the screws and hardware provid
• The stairwell allows the gate to be mounted less than 3" (7.62 cm) above the floor.
WARNING
TOO LOW! Less than 2" (5 cm)
IMPORTANT: DO NOT attempt to mount the brackets into uneven molding or wall base
Fig. 1
board trim, as the gate will not function properly.
DO NOT mount the gate less than 2" (5 cm) or more than 3" (7.62 cm) above the floor.
A
Make sure the mounting template is in a straight vertical position.
1. Using adhesive tape, attach the mounting template on the solid wood surface that you
have chosen for the hinged side of the gate.
2. Drill four 1/8" (3 mm) diameter starter holes into the mounting surface at the crosshatch
marks on the template.
3. Remove the template from the wall.
4. Drill each hole to a depth of 2" (5 cm).
5. Using hinge screws, screw the two hinge brackets
tabbed edge down (Fig. 1). Tighten the screws until the hinge brackets are securely
fastened to the mounting surface.
Fig. 2 6. Slide the hinge side of the gate
(Fig. 2).
B
A
Fig. 3
7. Squeeze the latch mechanism
mechanism until it snaps into place (Fig. 3).
D C

Before You Start

ed.
WARNING
TOO HIGH! More than 3" (7.62 cm)
Installation
into the mounting surface
A
B down through the hinges until it is securely seated
C and slide the upper latch housing
1 A
with
the
D over the latch