Knape & Vogt PDMTM115-1-35 Instrucciones De Instalación

Parts Included
A. One (1) Sliding Bin Assembly
(Slide brackets, sliding members and
platform pre-assembled)
B. Waste Bins (2)
C. One (1) Wire Accessory Basket (only on
single-bin models)
D. Two (2) Rear Slide Mounting Brackets
E. Door Brackets (2)
F. Four (4) #6-18 x 5/8" Phillips flathead
sheet metal screws for mounting door
brackets
G. Four (4) #10-24 x 1/4" Phillips pan head
machine screws
H. Eight (8) #7 x 1/2" Phillips pan head
sheet metal screw for mounting slide
members
Single Bin
Rear Slide
Platform
Mount
and Basket
Brackets
Disconnect
Lever
Slide Member
Brackets
Door Brackets
Tools Required
• Phillips head screwdriver
• Drill with 1/16" (1.5 mm) bit for drilling
pilot holes
• Tape measure or ruler
• Pencil
• Level
Product Assemblies
PDMTM115-1-35 PDMTM175-2-35
PDMTM12-1-35 PDMTM18-2-35
PDMTM145-1-50 PDMTM21-2-35
PDMTM15-2-35
2700 Oak Industrial Drive NE , Grand Rapids, MI 49505 USA
800.253.1561 • 616.459.3311 • www.kv.com
Top-Mount Waste And Recycling Unit
Installation Instructions
Note: This product is designed specifically for use with traditional 1-1/2" wide face frame style cabinetry. To use with non-
traditional face frame cabinetry, or Euro-style frameless cabinetry, additional blocking may be required to provide the correct
cabinet opening width.
Inspect all parts and read all instructions prior to beginning assembly and installation.
1.
If cabinet door is attached to cabinet, remove
hinges from cabinet frame and door,
and set door aside for use in Step 6.
Mark front location for attaching slides.
On face frame cabinetry, mark 14-3/4"
(for 35 qt. applications) OR 18-3/16" (for 50 qt.
applications) up from the top edge of bottom
frame cross rail on both front frame stiles. Mark
on interior edge of frame stile. This line will
indicate the slide centerline. Using a level, verify
that both marks on cabinet frame are level. To
properly locate the cabinet member of the slide
front to back and allow for a 2 mm setback, a
second mark should then be placed 1/2" back
from the front of the face frame. This mark, 1/2"
back from the front edge indicates the location
of the front mounting screws for left and right
slides. (FIGURE A)
Optional Step
Using 1/16" drill bit, drill pilot holes for
inserting screws.
2.
Mark rear location for attaching slides. On face frame cabinetry, measure 14-3/4" (for 35 qt.
Double Bin
applications) OR 18-3/16" (for 50 qt. applications) up from the cabinet bottom on the cabinet
Platform
back panel. If you have a recessed cabinet bottom that sits below the top of the bottom face
frame rail, you will need to add the amount of face frame reveal to this number. Mark this
location. (Example: cabinet bottom is 1/4" below the top edge of face frame = 14-3/4" + 1/4"
equals 15" high mark). Using a level, verify that both marks on cabinet back panel are level.
3.
On the 14-3/4" (for 35 qt. applications) OR 18-3/16" (for 50 qt. applications) height line
determine the centerline of the back panel and measure out from the centerline on either side.
Refer to Chart 1 below for dimensions. These marks will indicate where the inside edge of each
slide mounting bracket will sit. Align the rear slide mounting bracket to this mark, with the
bracket centered on the 14-3/4" (for 35 qt. applications) OR 18-3/16" (for 50 qt. applications)
vertical height line. Using two (2) #7 x 1/2" pan head sheet metal screws, attach bracket to
cabinet back panel. Repeat this process for attaching other rear-mounting bracket.
Optional Step
Using 1/16" drill bit, drill pilot holes for inserting screws.
Chart 1
Cabinet Opening
11-1/2"
12"
14-1/2"
15"
17-1/2"
18"
21"
©2016 Knape & Vogt. All rights reserved. Made in USA. Knape & Vogt ® reserves the right to change specifications without notice.
1/2"
Distance from Centerline
4-3/4"
5"
6-1/4"
6-1/2"
7-3/4"
8"
9-1/2"
Refer
to Chart
14-3/4" (35 qt.)
18-3/16" (50 qt.)
14-3/4" (35 qt.)
18-3/16" (50 qt.)
FIGURE A
310168_0416