Joovy 002 Manual De Instrucciones página 4

EN FR ES
• Connect lap and shoulder belts with locking clip as shown. See Figure 10.1.
• Re-buckle belt. Check that the lap belt dos not move by pulling and pushing hard on the doll carrier and base. If belt loosens or lengthens,
repeat procedure.
11 Unacceptable Vehicle Belt Systems
DO NOT use any of the following systems to secure the car seat.
• Lap Belts with Emergency Locking Retractor (ELR): This lap belt stays loose and can move until it locks in a sudden stop or crash.
• Combination Lap/Shoulder Belt with Retractor: Each strap has a retractor at one end and is attached to the latch plate at the other end.
• Passive Restraint-Lap or Shoulder Belt Mounted on Door.
• Passive Restraint-Lap Belt with motorized Shoulder Belt
• Lap Belts Installed Forward of Seat Crease
12 Installing Doll Car Seat with LATCH
• Remove doll carrier from base.
• Extend LATCH Attachment Strap to its maximum length.
• Place the base in a rear-facing position in the vehicle seat.
• Thread LATCH Attachment Strap inside and through the curved plastic piece under the base. See Figure 12.1. Make sure strap lays flat
and is not twisted.
• Push the connectors through the seat crease slots and hook them to vehicle lower anchors. See Figure 12.2. Pull firmly on connectors to
be sure they are attached.
• Tighten LATCH by pushing down hard on the base and pulling the adjustment belt.
• NEVER put two LATCH Attachment Strap connectors on one vehicle LATCH anchor unless specifically allowed by the vehicle
manufacturer.
Place the doll carrier in the base and make sure that it "clicks". Pull up on the doll carrier to be sure it is latched securely in the base.
• Check that the LATCH Attachment Strap stays tight and does not slip from the tightened position. If it does, try another seating position or
contact our Customer Service Department at (877) 456-5049 for assistance.
Maintenance
The locking mechanism and all plastic parts on the car seat should be inspected periodically to insure that they are secured properly and not
damaged or malfunctioning. The safety harness, fabric items and their stitching should also be inspected periodically to insure that they are
secured properly and not loose, torn or otherwise damaged.
Fabric fading may occur if the car seat is left in direct sunlight or for long periods of time. When not in use, store the car seat out of direct
sun.
Cleaning Your Doll Car Seat
Seat Pad: The fabric material on this carrier can be cleaned using mild household soap or detergent and warm water on a sponge or clean
cloth. Always allow the fabric to completely air dry before using the carrier.
If the carrier seat pad becomes heavily soiled it can be removed for more extensive cleaning. To remove the pad, unbuckle the straps from
the safety harness buckle. Pull the shoulder straps and waist/crotch straps through the slots in the pad and remove the pad. Machine wash
on a delicate cycle and line dry. DO NOT USE BLEACH. Reverse steps to reinstall the seat pad.
Harness Straps: Harness straps can be spot cleaned with a mild soap and water solution. DO NOT MACHINE WASH OR IMMERSE
HARNESS STRAPS IN WATER. Doing so may weaken the straps.
Plastic Parts: Parts can be cleaned by wiping with a mild soap and water solution. DO NOT USE BLEACH. Bleach may weaken plastic
parts.
We want you to be completely satisfied with your purchase of this product. Should you experience any difficulty in
assembling or using this product, or if you have any questions, please contact our Customer Service Department:
UNITED STATES – Joovy: (877) 456-5049, Hours 8:30 am – 5:00 pm Central Time.
CANADA – Elfe Juvenile Products: (800) 667-8184, Hours 8:30 am – 5:00 pm Eastern Time.
ONLY use to attach TOY doll products to vehicle LATCH anchors.
DO NOT use for actual child car seat or other restraint system.
Discard this product if it is ever involved in an actual vehicle accident.
DO NOT allow children to play with this product.
SATISFACTION GUARANTEED
Please log onto www.joovy.com to register your new Joovy product.
WARNING
!