LOCK ALARM 2104 Manual De Instrucciones

Instructions (English)
The Lock/Alarm Padlock is designed to help protect your valuable possessions from theft in 2 ways: (1) If the shackle is
cut through the alarm will sound, or (2) if the lock is repeatedly hit hard the internal shock sensor will activate the alarm.
The Lock/Alarm Padlock requires six LR54/AG10 alkaline batteries. One set of batteries are already installed inside the
Lock/Alarm Padlock. A spare set of batteries are also included so please keep in a safe place for future use. The LED
key also requires two LR54/AG10 batteries to operate the LED flashlight - a set of batteries are already installed.
IMPORTANT Before using the Lock/Alarm Padlock for the first time you will need to remove the battery protector
strip inside the padlock - follow the 'Battery Installation' instructions below.
Battery Installation
For security, the battery compartment can only be opened when the Lock/Alarm Padlock is in the "unlocked" mode.
(1) Insert the key into the lock and turn until the shackle is released.
(2) Using a small cross headed screwdriver remove the screw at the bottom of the hole in which the end of shackle fits
into. Next to the fixed end of the shackle there is a small rubber plug inside a small hole. Pull out this rubber plug to
reveal another screw, and remove this screw using the screwdriver.
(3) Once the two screws have been removed, the top and bottom parts of the lock can be separated. It is recommended
to do this (and step 4) by placing the Lock/Alarm Padlock on its side on a flat surface such as a table. Be careful to
separate the top and bottom parts only as far as shown in the photo #1. If the unit is new you should notice a
battery protector strip coming out from the battery compartment. Gently pull this battery protector strip out, making sure
the battery pack stays firmly fitted in the battery compartment, then follow step (5).
(4) To replace the batteries, remove the battery pack by lifting it out of the battery compartment as shown in the photo #2.
Insert new batteries into the battery pack ensuring the correct polarity as indicated, and then slide the battery pack back
into place.
(5) Replace the top section of the lock casing and tighten up the two screws. Replace the rubber plug into the smaller of
the two holes.
Using the Lock/Alarm Padlock
1. Insert the key into the lock and unlock the Lock/Alarm Padlock to release the shackle.
2. Guide the shackle through the item you wish to lock.
3. Insert the end of the shackle into the lock hole and push in until you hear a "beep".
4. Turn the key in the lock to the 'locked' position. It is now locked and alarmed.
5. To unlock the Lock/Alarm Padlock simply insert the key into the lock and turn until the shackle is released. When the
shackle is released the alarm automatically disarms.
Testing the Alarm
1. Insert the key into the lock and unlock the Lock/Alarm Padlock to release the shackle.
2. Rotate the shackle about 10-20 degrees so the end of the shackle is slightly to one side of the lock.
3. Push the shackle down. You should hear the alarm start to sound. To stop the alarm simply pull up the shackle.
Replacement Keys: For security reasons, replacement keys will only be issued to users who have proof of purchase and have logged their key number via
the website www.lockalarm.com. Once registered, in the event of key loss, the manufacturer will endeavour to supply a replacement key (a charge applies)
EXPERIENCING DIFFICULTIES? Email support@lockalarm.com or check the website www.lockalarm.com for troubleshooting hints.
Disclaimer: Lock/Alarm Padlock has been designed as a deterrent to theft. The manufacturer or supplier cannot accept any
liability for personal injury, property damage or loss.
Warning: The Lock/Alarm Padlock has a very loud siren which may cause ear damage if used at close range and/or for prolonged
periods of time. Do not hold close to ears and keep away from children.
LOCK ALARM PADLOCK
Photo #1
Product Code: 2104
Photo #2