Light Emitting Diode - EWT CHERITON LED CHT20 Manual De Instrucciones

Thermostat (T) - see Fig. 2
In order to maintain a certain room temperature, set the
controller to 'max.'. Operate the appliance at full power until
the required room temperature is reached. Set back the
thermostatic controller until the appliance switches off with an
audible "click". This temperature will be kept almost constant
by the thermostatic control switching on and off automatically.
Please note that the appliance can only be switched on when
the thermostat setting is higher then the room temperature.
Remote control - see Fig. 3
The maximum range of use is ~ 6 metres.
Warning: It takes time for the receiver to respond to the
transmitter.
Do not press the buttons more than once within two seconds
for correct operation.
Battery Information - see Fig. 3
1. To activate the remote control remove the battery isolation
strip, which is used to ensure your remote control reaches you
fully charged.
2. To replace the remote control battery, turn over the remote
control, and follow the diagram embossed on the remote control
3. Only use CR2025 or CR2032 size of batteries.
Discard Leaking Batteries
Dispose of batteries in the proper manner according to provincial
and local regulations.
Any battery may leak electrolyte
- if mixed with a different battery type,
- if inserted incorrectly,
- if all the batteries are not replaced at the same time,
- if disposed of in a fire,
- if an attempt is made to charge a battery not intended to be
recharged.
Disposal of Used Batteries.
Batteries may contain hazardous substances which could be
endangering to the environment and human health.
The symbol marked on the battery and /or packaging indicates
that used batteries should not be treated as municipal waste.
Instead they should be left at the appropriate collection point
for recycling.
By ensuring used batteries are disposed of correctly, you will help
to prevent potential negative consequences on the environment
and human health. The recycling of materials will help to conserve
natural resources.
For more information please contact your local authority.
Thermal Safety Cut-out
The built-in overheat cut-out switches off the appliance
automatically in the event of a fault! Switch off the appliance or
disconnect the mains plug from the socket.
Remove any obstructions which may have caused the
overheating. After a short cooling down phase, the appliance
is ready for use again! If the fault should occur again, see your
local dealer!
WARNING: In order to avoid a hazard due to inadvertent
resetting of the thermal cut-out, this appliance must not be
supplied through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on and off by
the utility.
Maintenance
WARNING: ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE ATTEMPTING ANY MAINTENANCE.

Light Emitting Diode

This fire is fitted with LED (Light Emitting Diode) bulbs in place
of traditional incandescent bulbs. These generate the same
light levels as traditional bulbs, but use a fraction of the energy
consumed.
Wall fixing
- see Fig. 1
Drill holes using a 6mm drill as illustrated. Insert plugs and
screws. The raw plug supplied is suitable for use in block walls
(special fasteners required on stud walls). Do not fully tighten
screws, leave the head of the screw at least 10mm away from
the wall. Place the keyhole slots on the fire over the screws and
lower into position.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER
SUPPLY BEFORE CLEANING THE HEATER.
For general cleaning use a soft clean duster – never use abrasive
cleaners. The glass viewing screen should be cleaned carefully
with a soft cloth.
DO NOT use proprietary glass cleaners.
To remove any accumulation of dust or fluff the soft brush
attachment of a vacuum cleaner should occasionally be used
to clean the outlet grille of the fan heater.
It is possible to clean the inner glass and logset by removing
the outer glass panel. To remove the outer glass, remove the
4 screws holding the grille in position, (see Fig.4), remove the
grille and lift clear the outer glass.
Refit the outer glass in reverse of above.
WARNING: do not operate the product without the grille and outer
glass in position as this may effect the operation of the heater.
Recycling
For electrical products sold within the European
Community.
At the end of the electrical products useful life it
should not be disposed of with household waste.
Please recycle where facilities exist. Check with your
Local Authority or retailer for recycling advice in your country.
After Sales Service
Your product is guaranteed for one year from the date of
purchase.
Within this period, we undertake to repair or exchange this
product free of charge (excluding lamps & subject to availability)
provided it has been installed and operated in accordance with
these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance with
this product, please contact the relevant sales company for
your location based on the information located at the back of
this lealfet.
Please retain your receipt as proof of purchase.