Esquema De Asignaciones Plvc8X1-G (Módulo Básico) - HAWE Hydraulik PLVC 8 Serie Manual Del Usuario

6.2 Esquema de asignaciones PLVC8x1-G (módulo básico)
Pin PLC PLC2 Connection data
Y3 U_BAT1
Y1 0 Coil 0 / 24VDC, max. 2ADC
Y2 1 Coil 1 / 24VDC, max. 2ADC
X2 Measurement input for Y1, Y2
W2 2 Coil 2 / 24VDC, max. 2ADC
X1 3 Coil 3 / 24VDC, max. 2ADC
W1 Measurement input for W2, X1
T1 4 Coil 4 / 24VDC, max. 2ADC
T2 5 Coil 5 / 24VDC, max. 2ADC
T3 Measurement input for T1, T2
S2 6 Coil 6 / 24VDC, max. 2ADC
S1 7 Coil 7 / 24VDC, max. 2ADC
S3 Measurement input for S2, S1
A3 U_BAT2
A1 IB0.0 10VDC...30VDC 9,4kOhm
A2 IB0.1 10VDC...30VDC 9,4kOhm
B2 IW64.0 0..10VDC 24kOhm
C2 IB0.2 10VDC...30VDC 9,4kOhm
B1 IB0.3 10VDC...30VDC 9,4kOhm
C1 IW66.0 0..10VDC 24kOhm
D1 IB0.4 10VDC...30VDC 9,4kOhm
D2 IB0.5 10VDC...30VDC 9,4kOhm
D3 IW68.0 0..10VDC 24kOhm
E2 IB0.6 10VDC...30VDC 9,4kOhm
E1 IB0.7 10VDC...30VDC 9,4kOhm
E3 IW70.0 0..10VDC 24kOhm
M2 50, 100, 125, 250, 500, 1000kB
M3 50, 100, 125, 250, 500, 1000kB
K3 RXD_1
J3 TXD_1
H3 IB1.7 RXD_2
J2 TXD_2
M1 IB3.1 Fq0 10..30VDC 7kOhm 5kHz
N1 IB3.2 Fq1 10..30VDC 7kOhm 5kHz
P1 IB3.0 Fq2 10..30VDC 7kOhm 5kHz
R1 IB3.3 Fq3 10..30VDC 7kOhm 5kHz
R2 IB3.4 Fq4 10..30VDC 7kOhm 5kHz
P3 IB3.5 Fq5 10..30VDC 7kOhm 5kHz
G3 IW40.0 0..5 / 0..10VDC / 4..20mA *1
F2 IW42.0 0..5 / 0..10VDC / 4..20mA *1
F1 IW44.0 0..5 / 0..10VDC / 4..20mA *1
G1 IW46.0 0..5 / 0..10VDC / 4..20mA *1
H1 IW104.0 0..5 / 0..10VDC / 4..20mA *1
J1 IW106.0 0..5 / 0..10VDC / 4..20mA *1
K1 IW108.0 0..5 / 0..10VDC / 4..20mA *1
K2 IW110.0 0..5 / 0..10VDC / 4..20mA *1
L3 IW48.0 IB48.0 0..10VDC / 10..30VDC *2
L2 IW50.0 IB50.0 0..10VDC / 10..30VDC *2
L1 IW52.0 IB52.0 0..10VDC / 10..30VDC *2
H2 IB3.7 IB4.0 ESTOP
G2 BSL
R3 U_BAT_Controller
F3 IW54.0 U_BAT_KL15
N3 U_SENSOR
P2 reserved
X3 PGND
C3 PGND
B3 PGND
W3 Sensor GND
N2 Termination
Description PLVC8x1-G
*1 Analog input: the configuration can be changed via software parameters.
Input resistance: 0..5 V DC = 470 kOhm / 0..10 V DC = 100 kOhm / C1 4..20 mA = 220 Ohm / C2 4..20 mA = 150 Ohm
*2 Analog or digital input: the configuration can be changed via software parameters.
Input resistance: 0..10 V DC = 100 kOhm / digital = 7 kOhm
*3 Can be used alternatively as digital input. Input resistance: 3-7 kOhm
*4 Use after interrupted firmware-download
*5 Used for EE-Safe or can be used alternatively as analog input.
c1 These input works on the main processor.
c2 These input works on the second processor.
Name
Valve Supply (Coils 0...7)
Coil A proportional Valve 0
Coil B proportional Valve 1
Coil A proportional Valve 2
Coil B proportional Valve 3
Coil A proportional Valve 4
Coil B proportional Valve 5
Coil A proportional Valve 6
Coil B proportional Valve 7
Valve Supply (Coils 8...15)
Digital Input IB0.0
Digital Input IB0.1
Analog Input 20
Digital Input IB0.2
Digital Input IB0.3
Analog Input 21
Digital Input IB0.4
Digital Input IB0.5
Analog Input 22
Digital Input IB0.6
Digital Input IB0.7
Analog Input 23
CAN1_H
CAN1_L
RS232 Data cable
RS232 Data cable
RS232 second Controller
RS232 second Controller
Digital Input IB3.1
Digital Input IB3.2
Digital Input IB3.0
Digital Input IB3.3
Digital Input IB3.4
Digital Input IB3.5
Analog Input 8 C2
Analog Input 9 C2
Analog Input 10 C2
Analog Input 11 C2
Analog Input 40 C1
Analog Input 41 C1
Analog Input 42 C1
Analog Input 43 C1
Analog Input 12 / dig. Input C2
Analog Input 13 / dig. Input C1
Analog Input 14 / dig. Input C1
Emergency Stop Input C1/C2
Firmware Download *4
Supply Input Controllers
Backup Supply Voltage *5
5V/200mA
120 Ohm to CAN_Low int.
D 7845 M Página 11
Note User
ESTOP Transistor 1 U_BAT
Also on/off Valve
Also on/off Valve
measurement input
Also on/off Valve
Also on/off Valve
measurement input
Also on/off Valve
Also on/off Valve
measurement input
Also on/off Valve
Also on/off Valve
measurement input
ESTOP Transistor 2
CAN Bus
CAN Bus
ST10 RS-232 RX
ST10 RS-232 TX
also dig. Input *3
also Frequency
also Frequency
also Frequency
also Frequency
also Frequency
also Frequency
for Joystick/Pot
for Joystick/Pot
for Joystick/Pot
for Joystick/Pot
for Joystick/Pot
for Joystick/Pot
for Joystick/Pot
for Joystick/Pot
ESTOP
for both Controllers
U_BAT
also Analog Input 15
GND
GND
GND
GND
Connection to Pin M3