Stanley Fatmax WPLEDS Manual De Instruccion página 3

• Use only with AC or DC charging adapters that are provided with unit. Plug in the charging adapter at the spotlight first, then
plug into the charging source.
• Do not overcharge: Recharge up to 5 hours maximum.
• After charging/recharging, disconnect charging adapter or extension cord and wait 5 minutes before use.
• Do not crush, cut, pull or expose charging adapter cords to extreme heat.
• Position charging adapter cords so they do not become entangled or become a safety hazard. Keep charging adapter cords
away from sharp edges.
• Do not open body casing. There are no user-serviceable parts inside.
• Do not operate the spotlight without the lens in place.
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when disconnecting.
• Do not attempt to charge the unit if the charger is damaged – return the charger to manufacturer for repair or replacement.
INSTRUCTIONS PERTAINING TO WATERPROOF SPOTLIGHTS
The rubber O-ring acts to preserve the waterproof qualities of the spotlight. The O-ring seals the end cap to prevent water
from entering the gap. An undamaged rubber O-ring, rubber bezel and lens, and proper sealing of the end cap before use are
very important.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Attempting to remove the rubber O-ring; use of the unit with a damaged O-ring, rubber bezel or lens; improper sealing
of the waterproof end cap; and/or submerging this unit in depths greater than 6 feet may cause the unit to no longer be
waterproof. Do not submerge the unit if these conditions exist or the unit could sustain permanent damage.
• Submerging this unit in depths greater than 6 feet and/or operating it in water temperature other than between 41ºF and
104ºF (5ºC and 40ºC) could result in leakage, warping or malfunction, causing permanent damage to the spotlight.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Stanley FatMax
the instructions carefully before using your new spotlight.
READING THE BATTERY/CHARGE STATUS LED INDICATOR
The battery and charging status LED indicator is located directly above the 12 volt DC charging port under the waterproof end
cap on the back of the unit.
END CAP DETAIL
It lights or flashes in three colors to indicate the following:
When charging:
Green & Red (flashing alternately): Battery is overheated due to extensive use or recharging. The charging process will stop at
this stage and will automatically resume after a cool down period of several minutes.
Green: Battery is in a fully charged state.
Orange: Battery is in a partially charged state.
Red: Battery needs to be recharged.
When operating:
Green: Battery is operating at full voltage.
Orange: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged.
Red (flashing): Battery is operating at extremely low voltage. The built-in low voltage protection has activated and the unit will
automatically shut down (after sounding several "beeps"). The unit must be recharged immediately.
WPLEDS_ManualENSP_032614.indd 4-5
. Read this Instruction Manual and follow
® Waterproof LED Spotlight
DOT ICON (FOR
ALIGNMENT TO THE
TRIANGULAR ICON ON
THE END CAP)
TRIANGULAR
ARROW ICON (FOR
ALIGNMENT
TO THE DOT ICON ON
THE REAR OF UNIT)
4
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE first use using either the 120 volt AC
charger or the optional 12 volt DC charger for approximately 3-5 hours. Charge after each use until the battery/charge status
LED indicator lights green.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least every 30 days.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Make sure the unit is thoroughly dry before charging or recharging. If the unit has been submerged, wipe it dry with a soft
cloth before opening the end cap. If water leaks into the charging port, the unit can sustain permanent damage.
• Never place the light face down on any surface when charging.
• Failure to keep the battery charged will cause permanent damage and result in poor performance.
Charging/recharging using the 120 volt AC charger
• Make sure the spotlight is turned off.
• Unscrew (counterclockwise) the waterproof end cap on the back of the unit and remove it.
• Insert the barrel connector of the AC charger into the 12 volt DC charging port on the back of the unit. Insert the plug end
into a (powered) standard North American 120 volt 60Hz outlet.
• Charge until the battery/charge status LED indicator lights green (approximately 3-5 hours).
• Replace the end cap on the unit, screwing clockwise until the triangular arrow on the end cap is pointing to the dot icon on
the rear of unit. Make sure it fits securely, but do NOT overtighten.
Charging/recharging using the 12 volt DC charger (optional accessory)
CAUTION: NEVER connect the 12 volt DC charger to a positive grounded vehicle.
• Make sure the spotlight is turned off.
• Unscrew (counterclockwise) the waterproof end cap on the back of the unit and remove it.
• Plug the barrel tip of the supplied 12 volt DC charger into the 12 volt DC charging port.
• Insert the 12 volt DC plug end into the accessory outlet of your vehicle or other 12 volt DC power source.
• Charge until the green battery status LED lights (approximately 3-5 hours). DO NOT CHARGE FOR LONGER THAN 5 HOURS
USING THIS METHOD.
• Replace the end cap on the unit, screwing clockwise until the triangular arrow on the end cap is pointing to the dot icon on
the rear of unit. Make sure it fits securely, but do NOT overtighten.
Note:
When using a vehicle's 12 volt DC accessory outlet as a charging source, be aware that some vehicles require you to turn on the ignition to power the
accessory outlet.
Important Notes:
• If either of the chargers is plugged into the spotlight while it is operating, the unit will not charge. The unit will begin
charging once the spotlight is turned off.
• If either of the chargers is plugged into the spotlight while the built-in low voltage protection is activated, the unit will
automatically turn off and begin charging.
• If the on/off trigger is pressed when charging, the spotlight may not operate until the charger is disconnected and the
spotlight is turned off, then on again.
• Once the unit begins charging, the spotlight will not operate until the charger is disconnected.
• When the battery/charge status LED indicator lights green, a "beep" will sound to indicate the charging process is completed.
OPERATING INSTRUCTIONS
Important note: When either charger is plugged into the 12 volt DC port, the unit is in charging mode. The spotlight will not
run with either of the chargers plugged in.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Never operate this spotlight unless the rubber O-ring, rubber bezel and lens are intact and properly seated; and the
waterproof end cap is securely in place.
• Never operate the spotlight in areas with high strength magnetic fields, such as in the vicinity of AC power generator, etc.
• Never operate this spotlight at depths greater than 6 feet.
• Never operate this spotlight in water temperatures other than between 41ºF and104ºF (5ºC and 40ºC).
• This spotlight is designed to operate for up to one hour under water.
Operating the spotlight
The On/Off Trigger turns the unit on and off, and is also used to choose either the high or low brightness setting.
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again within 5 seconds to use the spotlight in its low (dimmest) setting.
• Press the On/Off trigger a third time to turn the unit off.
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again after 5 seconds to turn the unit off.
or
5
3/26/2014 3:07:12 PM