Jasco myTOUCH SMART 35167 Manual Del Usuario

Outdoor/Indoor
Simple Set
Wireless Timer System
Clock vs. countdown
mode indicator
On/off Override
Turn connected device
on/off regardless of
schedule
My on/off times
Set custom on/off times
Preset schedules
Pick a preset that
suits your schedule
Backlight button
Press to see active programs
and activate backlight
I. Initial setup
1. Batteries
A. On the back of the wireless timer, pull out the plastic tab keeping the battery
from making a connection. You may need to remove the battery door if the tab
doesn't pull out easily.
B. If the clock does not start, remove the batteries and reinstall them following
the "+" and "–" polarities, ensuring they match the marked information within
the battery housing.
C. Replace the plastic battery door, ensuring that it snaps back into place. Press
the reset ( ) button in the lower right corner using a toothpick or pencil.
r
2. Set the current time
Use up ( ) and down ( ) arrows to set
current time, take note of AM or PM time.
Note: When daylight savings time occurs use the up
( ) and down ( ) arrows to adjust the time by 1 hour.
3. Mount receiver module
A. Mount the receiver on a wall near a GFCI
receptacle using a screw or nail. Install receiver
as far above the ground level as possible with
receptacle facing downward. Do not install
where receiver can be immersed or where
water will splash or drip onto receptacle.
Screw or nail head must extend at least 3/16"
out from the wall (nail or screw not included).
B. Hang the receiver from the hole at the top of
the unit.
4. Plug-in receiver module
A. Plug in the light or electronic device you
want the wireless timer to control into your
receiver module.
B. Plug the receiver module into your wall outlet.
C. Make sure your light/device is turned to the
"On" position. The lamp or device should not turn on.
Using timer as a remote control
1. Simply press the On/Off button to override timer programs to
turn your lights or devices On/Off.
2. The timer will follow the next timer program setting to turn your
light or device On/Off.
3. To deactivate any program, push button again so that the LED
is no longer illuminated.
FCC Statement
This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions: (1 this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications
to this equipment. Such modifications could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-3(B)/NMB-3(B)
FCC: QOB GE53121T
IC: 6924A - GE53121T
Wireless Timer
AM/PM Indicator
Up and down
arrows
Set current time
and schedule my
on/off times
Countdown
Set custom countdown
Reset button
Clears all current times
and schedules — resets
timer to factory settings
Plug-in Receiver
II. Programming options
1. Choose a preset schedule
There are 3 pre-programmed times that run individually
or simultaneously. Choose from the following:
"evening" (5pm-12am)
"morning" (5am-8am)
"all night" (6pm-6am).
When a preset or custom program is chosen, the blue LED
indicator light will turn on for 10 seconds showing that the
program is active.
If a preset schedule does not fit your needs, you can use a
combination of custom on/off times and presets.
Example: Using "evening" (5pm-12am) and adding a "my
off time" of 10pm will create a 5pm-10pm timer schedule.
2. Set custom on/off times
Press "my on time," then use up (
set on time. Press "my off time," then use up (
arrows to set off time. (If you set the "my on time" earlier than
the current time, it will not turn on until the next day at the time
scheduled.) Note: The first time the "my on time" is set after
pressing reset button, it will start at 6pm. The first time the off
time is set, it will turn off at 10pm. Use the countdown to turn on
the timer if needed immediately. When using "my on" and "my
off" times make sure the blue light is lit next to the button. You
can see active programs at any time by pressing the "bl" button.
3. Set a countdown
This feature turns the light on for a set period of time and
turns it off when time expires. Press "countdown," then use
up ( ) and down ( ) arrows to set from 1 minute to 24
hours. Once you reach your desired time setting, simply
walk away and the timer will begin counting down. Your last
time setting will be remembered the next time you use the
countdown feature.
Use the kickstand to place
anywhere in your home.
WARNING
RISK OF ELECTRIC SHOCK
• DO NOT USE WITH AN EXTENSION CORD
• PLUG DIRECTLY INTO A GFCI PROTECTED
ELECTRICAL OUTLET
• UNPLUG BEFORE CLEANING
• FULLY INSERT PLUG
• KEEP CHILDREN AWAY
RISK OF FIRE
• DO NOT EXCEED ELECTRICAL RATINGS
• DO NOT USE TO CONTROL APPLIANCES THAT CONTAIN
HEATING ELEMENTS (COOKING APPLIANCES, HEATERS,
IRONS, ETC.)
Mounting eyelet
Use to mount timer
near receptacle
) and down ( ) arrows to
) and down ( )
Use the keyhole on the back of
the timer to mount on a wall.
MADE IN CHINA
Distributed by Jasco Products Company LLC,
10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 1-year limited warranty.
Visit www.byjasco.com for warranty details.
Questions? Contact us at 1-800-654-8483
between 7:00AM–8:00PM CST.
125V~60Hz
Maximum load:
15A 1875W resistive
1250W tungsten 1/2HP
RAINTIGHT, NOT FOR WATER IMMERSION OR
FOR USE WHERE DIRECTLY EXPOSED TO WATER.
GE5350
Requires 3 AAA
batteries (included)
35167 V2 7/21/17