Publicidad
SETUP AND OPERATION
1.
Place the 4 CHANNEL FX PUSHER device on a fl at, stable surface. Connect the power supply
cable (not included) using the Power input connector (1). Make sure that the power cable
supports the power of the/s machine/s of FX you want to control.
2.
Make sure that the power switch (7) is in OFF position.
3.
The 4 CHANNEL DMX SWITCH supports up to 20A of resistive load, or 15A of inductive load.
Make sure that the consumption of all machines which will be activated at the same time does
not exceed the maximum allowed.
4.
Connect the DMX cable to the DMX IN connector (4). You can use either of the 3-pin or 5-pin
DMX IN connectors according to your needs.
5.
You can connect other machines and DMX devices using the DMX OUT connector (5).
6.
Connect the machine(s) which you want to control to the "POWER OUT" connectors (3). Each
output connector corresponds to a DMX channel which will be assigned later.
7.
Switch ON (7) the device 4 CHANNEL DMX SWITCH.
8.
If the 4 CHANNEL DMX SWITCH PACK device is receiving DMX signal, the led on "SIGNAL" (9) will
light up
9.
Assign the 4 operating DMX channels (13) using the buttons "UP" and "DOWN". Make sure that
the selected channels are free.
SECURITY CHANNEL
10. The 4 CHANNEL DMX SWITCH is equipped with a safety channel (10) that protects the 4
operating channels against any unintended activation. Assign the channel you want to use as
the safety channel by using the "UP" and "DOWN" buttons on the safety channel. Make sure
that the channel selected is free. The operating channel are subject to the permission of the
safety channel.
11. To unlock the safety channel, your DMX controller must send a value between 40% and 60% to
the security channel. When the safety channel is unlocked, the "ARMED" (12) led will light on and
the operating channel is ready to be activated.
12. After activating the desired channel, you should enable again the safety mode by sending to the
safety channel a value outside of the 40-60%.
13. The 4 CHANNEL DMX SWITCH also allows you to work without safety channel. To disable this
safety channel, simply press the "ENABLE / DISABLE" button (11) to disable position. The screen
of the safety channel will display "DIS" and the led "ARMED"(12) will be lit permanently. To re-
enable the security channel press again the button "ENABLE / DISABLE".
1.
Coloque el 4 CHANNEL DMX SWITCH PACK en una superfi cie llana y estable. Conecte la
alimentación de corriente mediante el conector powercon de entrada (1). Asegúrese de que el
cable de alimentación admite la potencia de la/s máquina/s de FX que quiere controlar.
2.
Asegúrese de que el interruptor de encendido (7) está en posición OFF.
3.
Conecte el cable DMX a la toma de entrada DMX "DMX IN" (4). Para su comodidad dispone de
una toma DMX de 3 pin y otra de 5 pin.
4.
Puede conectar otras máquinas y dispositivos DMX utilizando la toma de salida DMX "DMX
OUT" (5).
5.
Conecte las máquinas que desea controlar a las tomas "POWER OUT"(3). Cada toma corresponde
a un canal DMX que se asignará posteriormente.
6.
Encienda el dispositivo 4 CHANNEL DMX SWITCH PACK (7).
7.
Si el 4 CHANNEL DMX SWITCH PACK está recibiendo señal DMX se encenderá el led "SIGNAL"(9).
8.
Asigne los cuatro canales DMX (13) deseados mediante los botones "UP" y "DOWN" de cada
canal. Asegúrese de que los canales seleccionados estén libres.
4 CHANNEL DMX SWITCH PACK
/ MONTAJE Y OPERATIVA
INSTRUCTION MANUAL
Publicidad
