Electrical Safety; Description Of Device / Spare Parts - ATIKA ASP 10 TS-2 Manual Original

correctly installed and fulfil all conditions to ensure perfect
operation.
 Damaged safety devices and parts must be properly re-
paired or exchanged by a recognized, specialist work-
shop; insofar as nothing else is stated in the instructions
for use.
 Damaged or illegible safety labels have to be replaced.
 Do not allow any tool key to be plugged in!
Before switching on, checking always that all tools are re-
moved.
 Store unused equipment in a dry, locked place out of the
reach of children.
 Switch the machine off and remove the mains plug from the
socket when
Carrying out repair work.

Performing maintenance and cleaning

work.
Eliminating faults.

checking of connection cables whether they are swal-

lowed or damaged
Storage and transport

Leaving unattended (even during short interruptions).

Do not carry out repair operations on the machine
other than those described in section "Maintenance"
but contact the manufacturer or authorized customer
service centres.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer ser-
vice points.
Use only original spare parts and accessory parts.
Accidents can arise for the user through the use of
other spare parts. The manufacturer is not liable for
any damage or injury resulting from such action.

Electrical safety

 Design of the connection cable according to IEC 60245 (H
07 RN-F) with a core cross-section of at least
 5 x 1.5 mm² for a maximum cable length of up to 10 m
 Never use the machine with a power supply cable of over 10
m in length. Longer power supply cables will cause a drop in
voltage. The motor will not be able to provide its maximum
performance and the operation of the machine will be im-
paired.
 Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic mate-
rial of same mechanical stability or be covered with this ma-
terial.
 The connector of the connection cable must be splash-proof.
 When installing the power supply cable observe that it does
not interfere, is not squeezed, bended and the plug connec-
tion does not get wet.
 Wind off completely the cable when using a cable drum.
 Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do not
use the cable to pull the plug from the socket.
 Regularly check the extension cables and replace them if
they are damaged.
 Do not use any defective connection cables.
16
 When working outdoors, only use extension cables especial-
ly approved and appropriately labelled for outdoor use.
 Do not set up any provisional electrical connections.
 Never bypass protective devices or deactivate them.
The electrical connection or repairs to electrical parts
of the machine must be carried out by a certified elec-
trician or one of our customer service points. Local
regulations – especially
measures – must be observed.
Description of device /
Spare parts
 Please refer to the attached assembly and operating in-
struction sheet.
Pos. Order no. Designation
1 Preassembled device

2 Protective arm

3 Safety hook

4 Log lifter

5 359827 Wheel
6 Wheel axle

7 Transport support wheel

8 Fastener bag

9 Operating instructions

10 Assembly and operating instruction

sheet
11 Warranty declaration

12 Operating handle left

13 Operating handle right

14 Fixing claw

15 Base plate

16 Handle

359865 Splitting blade (ASP 10 / 12 TS-2)
17
359885 Splitting blade (ASP 14 TS-2)
18 Splitting column

19 Locking screw for lifting height ad-

justment
359872 On/Off switch (ASP 10 / 12 TS-2)
20
359883 On/Off switch (ASP 14 TS-2)
359871 Motor (ASP 10 / 12 TS-2)
21
Motor (ASP 14 TS-2)
359882
22
Oil tank lock
359867
22A
Dip stick
23 Oil seal (not illustrated)

359863 Cylinder (ASP 10 TS-2)
24 359878 Cylinder (ASP 12 TS-2)
359880 Cylinder (ASP 14 TS-2)
25 Return lever

26 Transport drawbar

27 Safety chain

28 359868 Return spring
29 359869 Oil drain plug
30 359873 Hydraulic valve (not illustrated)
31 400142 Hydraulic oil (1 litre)
32 359807 Safety label
regarding protective