Mounting Instructions - RAVAK NEREZ ROSA II Serie Manual Del Usuario

GB
Installation of stainless
steel handle ROSA II
The handle is intended for ROSAII L(P)
It can serve as an elegant accessory, or as a bathtub support piece for disabled people.
If possible, mount the handle prior to installing the bathtub.
However, another advantage of this handle type lies in the fact that it can also be mounted
on an already installed bathtub.
To find the optimal location for the handle, we recommend you to try it directly on the
bathtub.
ROSAII L - stainless steel L, ROSAII P - stainless steel P.

Mounting instructions

1. Insert the bolts ( ) into the handle ( ) and secure with a set-screw ( ) Measure the 3
accurate spacing " " for the bolts, and remove the bolts again. x
2. Place the handle into the chosen location, check its seating on the tub, its function and
appearance in this position. Use a pencil to mark out the accurate outline of both seating faces of the handle ends.
3. Remove the covering paper from the template ( ) and apply the transparent self-adhesive foil as accurately as possible to the outline drawn on the
bahtub. Control the " " spacing, and, if needed, adjust the spacing of the openings axis (tolerance 0,5 mm). Drill the Ø 3 mm holes in the positions x
marked on the template. Remove the template. To continue, choose one of the following ways:
A) Mounting the handle prior to bathtub installtion
4. Enlarge the pre-drilled Ø 3 mm holes to Ø 8 mm. Be very careful when drilling, use use only little force with the drill set at higher speed, vertically
towards the tub.
5. Insert the threaded bolt ( ) into the opening and tighten it slightly. Set the handle on the bolt ends (the set-screws must point to the bathtub), and 3
tighten the set-screws with the allen key ( ). Check seating of the handle and the bolts. Some minor measurement inaccuracies can be adjusted by
re-drilling the openings to the max. Ø 10 mm.
6. Apply a layer of silicon putty (from the backside of the bathtub) around the opening for the washer ( ) before you attach the handle definitely. Use
only appropriate strength to tighten the bolts ( ) to avoid damaging the bathtub.
B) Mounting the handle on an already installed bathtub
7. This way of installing is more difficult, demanding use of special tools; we therefore recommend you to have it done by professionals. Check
spacing of the bolts ( ) on the handle and compare it to spacing of the holes pre-drilled in the bathtub adjust the spacing if necessary. Enlarge the 3
holes carefully to Ø 11 mm. In the hole, prepare a tapered enlargement (Ø 13 mm, depth 1,5 mm) for the nut-rivet. Try out recessing of the handle
complete with the rivets don´t clinch the rivets yet. Use the riveting tool to fit the nut-rivets ( ) into the openings.
8. Screw the bolts ( ) with the rubber "O" ring, and set the handle on. Fix the handle by tightening the set-screws ( ). 3
C) Installing the handle on a polyurethane-reinforced bathtub, PU-PLUS
Bathtubs reinforced by sprayed layer of PU have, compared to the laminate-reinforced ones, thicker sides and especially rims. Therefore it is
necessary to measure thickness of the rim first.
9. If the bathtub side is less than 12 mm thick, follow the instructions given in paragraph or .
10. If the PU reinforcement in the rim is more than 15 mm thick, install the handle this way:
11. In the location of ø 3 mm holes drill ø 6,7 mm holes and make an M 8 thread.
12. Screw the pegs no. with rubber "O-ring" in the thread. To tighten them, use appropriate force (up to 5 Nm) so as not to damage the thread in the 3
plastic bathtub rim.
13. Set the handle on and fix it there.
ATTENTION:
Do not use any mechanical abrasives (e.g. grinding paste) or aggresive chemicals (e.g.thinners, acetate etc.) to maintain the product. The
manufacturer takes no responsibility for any damage caused by inappropriate installation, use or maintenance. Maintain the product only by wiping
its paint coated or chrome parts, glass fillings and plastic pieces with special cleaning preparations.
The manufacturer recommends the RAVAKANTICALC product range for maintenance:
RAVAK CLEANER to remove soap deposits and dirt from glass surfaces, shower enclosure frames, enamel and acrylic bathtubs, washbasins and
water taps.
RAVAK DESINFECTANT a special detergent with high anti-bacterial and fungicidal effects.
The manufacturer reserves the right to innovate the product. The warranty is valid 24 months from the date of purchase. For further information
about installation, use, and maintenance, contact your local dealer.
Disposal of the packing materials and of the product after its lifetime:
Any further useful packing materials (e.g. cardboard, building paper, or PE foil) please use or recycle.
Packing materials you have no use for must be disposed of only in a safe and environmental way according to valid law norms of each country.
After the lifetime of the product has elapsed, please give all the useful parts (e.g. metal) for further use or for recycling as usual according to the law
norms of the country.
tel.: 318 427 111, fax: 318 427 269, e-mail:
The manufacturer reserves the right to change the price, technical parameters or other facts without
bathtubs.
1
8
7
5
RAVAK a.s., Obecnická 285, 261 01 Pøíbram 1, ÈR
a prior notice and shall bear no responsibility for the printing errors.
GB
1. ROSA II L(R) stainless steel
2. Set-screw with internal hexagon
3. M8 Bolt
4. Washer
5. Nut M8
6. M8 nut-rivet
7. Allen key 3
8. Template (a,b)
2
9. "
4
6
A B
info @ravak.cz, www.ravak.com, www.ravak.cz
BASIC MOUNTING KIT
Æ
8,5 mm
Æ
" 16 x 12
2
1 pc
2 pcs
2 pcs
2 pcs
2 pcs
2 pcs
1 pc
2 pcs
2 pcs