Operation - Craftsman 351.215132 Manual Del Usuario

215132_Bil_oipm_V1:PN30635.00
EXTENSION CORDS
• The use of any extension cord will cause some drop
in voltage and loss of power.
• Wires of the extension cord must be of sufficient size
to carry the current and maintain adequate voltage.
• Use the table to determine the minimum wire size
(A.W.G.) extension cord.
• Use only 3-wire extension cords having 3-prong
grounding type plugs and 3-pole receptacles which
accept the tool plug.
• If the extension cord is worn, cut, or damaged in any
way, replace it immediately.
Extension Cord Length
Wire Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.W.G.
Up to 25 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
25 to 50 ft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
NOTE: Using extension cords over 50 ft. long is not
recommended.
MOTOR
The sander is assembled with motor and wiring
installed as an integral part of the tool.
The permanently split capacitor motor has the following
specifications:
Horsepower (Continuous Duty) . . . . . . . . . . . . . . . . . .
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Amps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5
Hertz . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Phase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single
RPM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3500
Rotation (viewed from left side) . . . . . . . . . . . Clockwise
ELECTRICAL CONNECTIONS
WARNING:
All electrical connections must be per-
formed by a qualified electrician. Make sure tool is off
and disconnected from power source while motor is
mounted, connected, reconnected or anytime wiring is
inspected.
Motor is assembled with approved, 3-conductor cord to
be used at 120 volts. Motor is prewired at the factory for
120 volts.
The power lines are inserted directly onto the switch.
The green ground line must remain securely fastened
to the frame to properly protect against electrical shock.
The power supply to the motor is controlled by a single
pole locking rocker switch.
• Remove the key to prevent unauthorized use.
Refer to Figures 6-14.
DESCRIPTION
Craftsman 2 x 6" Belt and Disc Sander has a 2" x 42"
belt and 6" disc for deburring, beveling and sanding
wood, plastic and metal. The sander has a fan-cooled
4/14/2009 5:38 PM Page 5

OPERATION

HP continuous duty motor. Belt speed is 4400 FPM and
the disc rotates 3500 RPM. The belt table tilts 0 to 60°
and the disc table tilts 0 to 45° for angle sanding. The
quick release tension and tracking mechanism makes
belt changing quick and easy. Belt platen is removable
for contour sanding. Belt housing swivels from vertical
to horizontal for sanding large workpieces. Disc guard
" dust collection chute.
has 1 1 /
2
SPECIFICATIONS
Belt size . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 42", 80 grit
Belt platen area . . . . . . . . . . . . . . . . . . . . . . . . . 2 x 7
Belt table dimensions . . . . . . . . . . . . . . . . . . . . 9 x 6¾"
Belt table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 60°
Belt speed . . . . . . . . . . . . . . . . . . . . . . . . . . . 4400 FPM
Disc diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6"
Disc table dimensions . . . . . . . . . . . . . . . . . . 8
Disc table tilts . . . . . . . . . . . . . . . . . . . . . . . . . . 0 to 45°
Disc dust chute diameter . . . . . . . . . . . . . . . . . . . . . 1
Disc speed . . . . . . . . . . . . . . . . . . . . . . . . . . 3500 RPM
Base dimensions . . . . . . . . . . . . . . . . . . . . . . 9
Switch . . . . . . . . . . . . . . . . . . . . . . . . SP, Locking rocker
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 lbs
Shipping weight . . . . . . . . . . . . . . . . . . . . . . . . . . 35 lbs
1 /
3
WARNING:
Operation of any power tool can result in
foreign objects being thrown into the eyes, which can
result in severe eye damage. Always wear safety gog-
gles complying with United States ANSI Z87.1 (shown
on package) before commencing power tool operation.
Safety goggles are available at Sears retail stores or
catalog.
CAUTION:
Always observe following safety precautions.
SAFETY PRECAUTIONS
• Whenever adjusting or replacing any parts on the
tool, turn switch OFF and remove the plug from
power source.
• Recheck table knobs. They must be tightened
securely.
• Make sure all guards are properly attached. All
guards should be securely fastened.
• Make sure all moving parts are free and clear of any
interference.
• Make sure all fasteners are tight and have not
vibrated loose.
• With power disconnected, test operation by hand for
clearance and adjust if necessary.
• Always wear eye protection or face shield.
• Make sure abrasive belt always tracks properly.
Correct tracking gives optimum performance.
• After turning switch on, always allow belt to come up
to full speed before sanding or grinding.
• Be sure motor runs clockwise on disc side. Abrasive
belt must travel down.
1 /
3
5
"
1 /
4
"
3 / x 5 7 /
16 16
"
1 /
2
"
1 / x 8 9 /
16 32