Connecting To The Network - Korenix JETCON 3301 Serie Guía De Instalación Rápida

Introduction
The JetCon 3301 Gigabit Ethernet media converter series is designed to convert 1000Base-T
signals to 1000Base-SX/LX signals, 1501 Fast Ethernet media converter series (10/100Base-
TX to 100Base-FX). They greatly extend the connection range of Ethernet device to transmit
& receive data via fiber cable without performance degradation. Both converters support
auto-negotiation, flow control function on RJ-45 copper port. The JetCon 3301 converter
series also supports jumbo packets up to 10KB. With the Link Loss Forwarding technology,
the JetCon 3301 / 1501 can fast detect the broken link on RJ-45 port and force the
disconnection on the fiber port immediately. JetCon 3301 / 1501 also features diagnostic
LEDs, which displays power, link and activity, allowing you to quickly detect and correct
problems on the network.
Package Check List
Unpack the box, you will find
4
One media converter
4
One power adapter
4
Quick installation guide
Wiring the Power Input
4 Plug the power adapter to the converter and
connect to an outlet or power strip

Connecting to the Network

1. Connecting the RJ-45 port: Connect one side of an Ethernet cable into the UTP port of
JetCon converter, while the other side is connected to the attached networking device. The
UTP port supports auto MDI/MDIX function. The JetCon 1501 supports 10Base-T/100Base-
TX. The JetCon Ethernet 3301 supports 1000Base-T Gigabit copper and does not support
10Base-T/100Base-TX Ethernet environment.
2. Connecting the Fiber port: Connect the fiber port of your JetCon to another one located
on another Fiber Ethernet device. The JetCon 3301 converter supports Gigabit fiber
1000Base-LX/SX and provides different types of fiber connectors such as SC, LC for multi-
mode or single-mode fiber cables (JetCon 1501 series supports 100Base-FX with SC or ST
fiber connector). Please be sure signal connection correctly (Rx-to-Tx or Tx-to-Rx). Wrong
signal connection will cause fiber ports not to work normally.
3. For JetCon 1501, set operation mode of the Fiber port: set operation mode of the Fiber
port: Users can use DIP switch located at right side of the converter to set the fiber port in two
different operation modes, full-duplex and half-duplex. The factory default is set as full duplex
mode
The LED indicators of JetCon 3301 media converter
LED Color
POWER
Yellow
TX
Green
RX
Green
LINK
Green
The LED indicators of JetCon 1501 media converter
LED Color
POWER
Yellow
Green
FDX
Green
10/100M
Yellow
LNK/ACT
Mounting the unit on the media converter chassis
JetCon 3301 / 1501 can be installed on the media
converter chassis and uses the DC power provided
by chassis Rack-1001 (single power supply) /
Rack-1002 (redundant power supply.
Korenix Customer Service
KoreCARE is Korenix Technology's global service center,
where our professional staffs are ready to solve your
problems at any time.
Korenix global service center's e-mail is KoreCARE@korenix.com
Half Duplex
Full Duplex
Status Description
On Power On
Blinking
Transmitting data on RJ-45 port
Blinking Receiving data on Fiber port
On Port in connection
Status Description
On Power On
On
Set Fiber port in Full-Duplex mode
Off Set Fiber port in Half-Duplex mode
Blinking
Data collision occurs
On RJ-45 port is connected with 100M device
Off
RJ-45 port is connected with 10M device
On 10/100M port for connection
Blinking 10/100M port for data activating