EcoNet Rheem Instrucciones De Instalación

Rheem Home Comfort WiFi Module Instructions
®
Learn more at Rheem.com/EcoNet
WATER HEATER
BEFORE YOU BEGIN: This WiFi module is intended to be used on Rheem EcoNet enabled
equipment. Using a cell phone (or other WiFi device), please make sure that WiFi signals
are present in the area where this module is being installed. This module is compatible
with 802.11 b/g/n networks.
Easy Installation Instructions
1. Locate and write down the unique Media Access Control (MAC) address of your module in the
space below and use it later for online registration and WiFi setup. The MAC address can be
found on the back of the WiFi module on the product label.
(MAC) Address: _____-_____-_____-_____-_____-_____
Media Access Control
(MAC) Address location
2. Attach the provided cable to your WiFi module.
WiFi module
3. Using the provided double sided adhesive tape, affix your WiFi module
to the side of your equipment on a flat surface
Attach the other end of the cable to equipment per the diagram below.
RJ25
Easy WiFi Setup Instructions
After your WiFi module is installed and powered, all LEDs will be blinking simultaneously indicating
that the WiFi module is ready to be set up with your WiFi network.
1. Download the free "EcoNet" App from Rheem available at the iTunes App or Google Play stores.
NOTE: You must be within 5 feet of unobstructed distance from your module for activation.
2. Follow the simple on screen steps to create your EcoNet account and activate your WiFi module.
You will need your unique Media Access Control (MAC) address during this process.
3. When your registration is complete, you should be able to control your Rheem equipment and
receive alerts through the Rheem EcoNet App.
HELPFUL TIPS
• If you need to reset your wireless network on the WiFi module, press the 'WLAN SETUP'
button.
• All three LEDs will start blinking simultaneously when the 'WLAN Setup' button is
pressed.
• Log in to your EcoNet account and repeat the online steps. You may need to re-enter the (MAC) address if
prompted.
Top LED indicates power and connection
to equipment
Middle LED indicates a WiFi signal
Lower LED indicates an active WiFi
connection
The WLAN SETUP button is used to
reset the WiFi configuration/connection.
CHAUFFE-EAU
Instructions pour le module WiFi confort au foyer Rheem
Apprenez-en davantage sur Rheem.com/EcoNet
AVANT DE COMMENCER : Ce module WiFi est conçu pour être utilisé avec un
équipement qui accepte Rheem EcoNet. En utilisant un téléphone cellulaire (ou un autre
appareil WiFi), veuillez vérifier que les signaux WiFi sont bien présents là où vous installez
ce module. Ce module est compatible avec les réseaux 802.11 b/g/n.
Instructions d'installation facile
1. Repérez et inscrivez l'adresse unique de contrôle d'accès au support (MAC) sur votre module
dans l'espace ci-dessous et utilisez-la plus tard pour l'enregistrement en ligne et l'installation
WiFi. L'adresse MAC se trouve au dos du module WiFi sur l'étiquette de produit.
Addresse MAC : _____-_____-_____-_____-_____-_____
BEFORE YOU BEGIN: This WiFi module is intended to be used on Rheem EcoNet enabled
equipment. Using a cell phone (or other WiFi device), please make sure that WiFi signals
are present in the area where this module is being installed. This module is compatible
with 802.11 b/g/n networks.
Easy Installation Instructions
1. Locate and write down the unique Media Access Control (MAC) address of your module in the
space below and use it later for online registration and WiFi setup. The MAC address can be
found on the back of the WiFi module on the product label.
(MAC) Address: _____-_____-_____-_____-_____-_____
2. Attach the provided cable to your WiFi module.
WiFi module
Sample
3. Using the provided double sided adhesive tape, affix your WiFi module
to the side of your equipment on a flat surface
Attach the other end of the cable to equipment per the diagram below. Do not connect the
WiFi module to R (24VAC).
R
E1
E2
C
2FT cable
PN: RCPN-AMP03-0013111101-0001
Easy WiFi Setup Instructions
After your WiFi module is installed and powered, all LEDs will be blinking simultaneously indicating
that the WiFi module is ready to be set up with your WiFi network.
1. Download the free "EcoNet" App from Rheem available at the iTunes App or Google Play stores.
NOTE: You must be within 5 feet of unobstructed distance from your module for activation.
2. Follow the simple on screen steps to create your EcoNet account and activate your WiFi module.
You will need your unique Media Access Control (MAC) address during this process.
3. When your registration is complete, you should be able to control your Rheem equipment and
receive alerts through the Rheem EcoNet App.
HELPFUL TIPS
• If you need to reset your wireless network on the WiFi
module, press the 'WLAN SETUP' button.
• All three LEDs will start blinking simultaneously when
the 'WLAN Setup' button is pressed.
• Log in to your EcoNet account and repeat the online
steps. You may need to re-enter the (MAC) address if prompted.
Instructions pour le module WiFi confort au foyer Rheem
Apprenez-en davantage sur Rheem.com/EcoNet
AVANT DE COMMENCER : Ce module WiFi est conçu pour être utilisé avec un
équipement qui accepte Rheem EcoNet. En utilisant un téléphone cellulaire (ou un autre
appareil WiFi), veuillez vérifier que les signaux WiFi sont bien présents là où vous installez
ce module. Ce module est compatible avec les réseaux 802.11 b/g/n.
Instructions d'installation facile
1. Repérez et inscrivez l'adresse unique de contrôle d'accès au support (MAC) sur votre module
dans l'espace ci-dessous et utilisez-la plus tard pour l'enregistrement en ligne et l'installation
WiFi. L'adresse MAC se trouve au dos du module WiFi sur l'étiquette de produit.
Addresse MAC : _____-_____-_____-_____-_____-_____
HVAC
Sample
Media Access Control
(MAC) Address location
R
E1 E1
E2 E2
C C
PN: RCPN-AMPO8-0014090301-0001
RJ25
Top LED indicates power and connection
to equipment
Middle LED indicates a WiFi signal
Lower LED indicates an active WiFi
connection
The WLAN SETUP button is used to
reset the WiFi configuration/connection.
CVC
Exemple
Emplacement de
l'adresse de contrôle
d'accès au support (MAC)
WATER HEATER
+ HVAC
BEFORE YOU BEGIN: This WiFi module is intended to be used on Rheem EcoNet enabled
equipment. Using a cell phone (or other WiFi device), please make sure that WiFi signals
are present in the area where this module is being installed. This module is compatible
with 802.11 b/g/n networks.
Easy Installation Instructions
1. Locate and write down the unique Media Access Control (MAC) address of your module in the
space below and use it later for online registration and WiFi setup. The MAC address can be
found on the back of the WiFi module on the product label.
(MAC) Address: _____-_____-_____-_____-_____-_____
Media Access Control
(MAC) Address location
2. Attach the provided cable to your WiFi module.
WiFi module
3. Using the provided double sided adhesive tape, affix your WiFi module
to the side of your equipment on a flat surface
Attach the other end of the cable to equipment per the diagram below. Do not connect the
WiFi module to R (24VAC).
R R
E1 E1
E2 E2
C C
RJ25
RJ25
Splitter
PN: RCPN-AMP07-0014072201-0001
Easy WiFi Setup Instructions
After your WiFi module is installed and powered, all LEDs will be blinking simultaneously indicating
that the WiFi module is ready to be set up with your WiFi network.
1. Download the free "EcoNet" App from Rheem available at the iTunes App or Google Play stores.
NOTE: You must be within 5 feet of unobstructed distance from your module for activation.
2. Follow the simple on screen steps to create your EcoNet account and activate your WiFi module.
You will need your unique Media Access Control (MAC) address during this process.
3. When your registration is complete, you should be able to control your Rheem equipment and
receive alerts through the Rheem EcoNet App.
HELPFUL TIPS
• If you need to reset your wireless network on the WiFi
module, press the 'WLAN SETUP' button.
• All three LEDs will start blinking simultaneously when
the 'WLAN Setup' button is pressed.
• Log in to your EcoNet account and repeat the online
steps. You may need to re-enter the (MAC) address if prompted.
Top LED indicates power and connection
to equipment
Middle LED indicates a WiFi signal
Lower LED indicates an active WiFi
connection
The WLAN SETUP button is used to
reset the WiFi configuration/connection.
CHAUFFE-EAU + CVC
Instructions pour le module WiFi confort au foyer Rheem
Apprenez-en davantage sur Rheem.com/EcoNet
AVANT DE COMMENCER : Ce module WiFi est conçu pour être utilisé avec un
équipement qui accepte Rheem EcoNet. En utilisant un téléphone cellulaire (ou un autre
appareil WiFi), veuillez vérifier que les signaux WiFi sont bien présents là où vous installez
ce module. Ce module est compatible avec les réseaux 802.11 b/g/n.
Instructions d'installation facile
1. Repérez et inscrivez l'adresse unique de contrôle d'accès au support (MAC) sur votre module
dans l'espace ci-dessous et utilisez-la plus tard pour l'enregistrement en ligne et l'installation
WiFi. L'adresse MAC se trouve au dos du module WiFi sur l'étiquette de produit.
Addresse MAC : _____-_____-_____-_____-_____-_____
Sample
R
E1
E2
C