Tripp-Lite EnviroSense2 El Manual Del Propietario

EnviroSense2 (E2)
Environmental Sensor Module
Overview
• Three E2 models are available to monitor
temperature, humidity, contact closures or to
actuate contact closures. For use with Tripp Lite LX
Platform devices.
Installation
E2 sensor modules are compatible with LX Platform devices including: WEBCARDLX, WEBCARDLXMINI, PDU3E-Series PDUs, PDU3XE-Series PDUs and Single-phase
PDUs with slotted or integrated "LX" interfaces.
MODEL NAME TEMPERATURE
E2MT X
E2MTDO X
E2MTHDI X
Connecting the E2 Module to an LX Platform Device:
1
Using the included USB cable, plug the USB-A connector into the LX Platform device's USB-A receptacle
(refer to the device documentation to find the appropriate port). Then plug the cable's USB Micro-B connector
into the E2 module's USB Micro-B port.
Note: Up to three E2 modules can be daisy-chained together by connecting the USB-A port of the first module to the USB
Micro-B port of the second, then connecting the USB-A port to the USB Micro-B port of the third module. The module will
perform optimally in a properly ventilated environment.
2
The E2 module will appear as 'SensorXXXX' in the PowerAlert Device Manager, where XXXX are the last four digits of the E2's serial number. To view the E2, go to
Overview and select the module from the Device dropdown menu.
Feature Identification
Top View
3
1
USB-A
Connector View
3 2
5
Bottom View
5
4
Warranty and Product Registration
LIMITED WARRANTY
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in
material and workmanship for a period of 2 years from the date of initial purchase. If the product should prove defective
in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion. Service under
this Warranty can only be obtained by your delivering or shipping the product (with all shipping or delivery charges prepaid)
to: Tripp Lite, 1111 W. 35th Street, Chicago, IL 60609, USA. Seller will pay return shipping charges. Call Tripp Lite
Customer Service at (773) 869-1234 before sending any equipment back for repair.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE
OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF
MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS
WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow
limitations on how long an implied warranty lasts, and some states do not allow the exclusion or limitation of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This Warranty gives you specific
legal rights, and you may have other rights which vary from jurisdiction to jurisdiction.)
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or
safe for the use intended. Since individual applications are subject to great variation, the manufacturer makes no
representation or warranty as to the suitability or fitness of these devices for any specific application.
PRODUCT REGISTRATION
Visit tripplite.com/warranty today to register your new Tripp Lite product. You'll be automatically entered into a drawing
for a chance to win a FREE Tripp Lite product! (No purchase necessary. Void where prohibited. Some restrictions apply.
See website for details.)
19-09-317-9335D2.indb 1
Owner's Manual
Español 2 • Français 3 •  4
• When temperature and humidity values exceed
user-set limits or monitored contacts change state,
the event is recorded in the event log of the LX
Platform device's PowerAlert
interface.
HUMIDITY
X
1
Terminal Block Connector (included with all modules except E2MT): See below for details.
2
USB Micro-B Connector: Connects to an LX Platform device or another E2 module in the chain.
3
USB-A Connector: Connects to another E2 module.
4
Retention Harness: Use a cable tie (if applicable, not included) to secure the E2 module or USB cable
connections.
2
4 5
Cable Management Channels: Help secure the USB cables by routing them through these channels.
6
Magnets: Enable simple installation or re-positioning on a metal rack or other metallic surface.
USB Micro-B
Connector View
Contact Closure Connections:
Digital Inputs (E2MTHDI):
Only dry contact open/closed connections are allowed. The input requires an isolated dry contact. Typical
voltage: 5VDC; typical current: 18mADC.
Digital Outputs (E2MTDO):
Maximum voltage across dry contacts: 48VDC/30VAC; maximum current rating: 400mA.
Pin assignments can be found in the table below.
4
Note: The E2MTDO supports digital outputs in place of inputs.
The pin assignments are the same, with outputs in place of inputs.
Contact Closure Table (Pins are numbered from left to right)
Pin Number
6
1
2
3
4
1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support
Copyright © 2019 Tripp Lite. All rights reserved.
Device Manager
®
DIGITAL IN DIGITAL OUT
X
X
Description Normally Open/Closed
Contact 1
Contact 2
FCC Notice, Class A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense. The user must use shielded cables and
connectors with this equipment. Any changes or modifications to this equipment not expressly approved by Tripp Lite
could void the user's authority to operate this equipment.
Regulatory Compliance Identification Numbers: For the purpose of regulatory compliance certifications and
identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the
product nameplate label, along with all required approval markings and information. When requesting compliance
information for this product, always refer to the series number. The series number should not be confused with the
marketing name or model number of the product.
Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause
the failure of the life support equipment or to significantly affect its safety or effectiveness is not recommended.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.
1
WARRANTY REGISTRATION
Register your product today and be
automatically entered to win an ISOBAR
surge protector in our monthly drawing!
tripplite.com/warranty
• Up to three E2 modules can be daisy-chained
together.
USB Micro-B
Connector
1
Normally open
Normally open
+ IN 1 – + IN 2 –
USB-A
Connector
19-09-317 93-35D2_RevE
10/29/2019 12:20:16 PM