Publicidad
Idiomas disponibles
Idiomas disponibles
STEP 1
1. Place the M hinge wedges on the markings of part 6 and fasten
them with (4x12mm) X screws.
2. Fit the (6x30mm) A pegs to the bottom and to the top of part 6.
M
2
X
4
6
A
4
STEP 2
1. Fasten the part 6 to the piece 1 using the H angle and the
(4x12mm) X screws.
2. Fasten the parts 9 to the parts 1 & 10 with the T angles and
the (4x12mm) X screws.
X
34
9
10
H
5
1
T
6
1. Fit the (6x30mm) A pegs in the pieces 2 & 3
STEP 3
2. Fit the part 3 between the parts 2.
3. Fit the parts 2 in the part 1, and then fasten them with
A
12
(3,5x40mm) Y screws.
2
3
Y
4
2
1
STEP 4
1. Fit the (6x30mm) A pegs in the part 5.
2. Fit the parts 5 & 6 in the part 1, and then fasten them with
A
4
the (3,5x40mm) Y screws.
Y
2
5
1
6
STEP 5
1. Align the RO Casters with the part 1, and then fasten them
with (4x12mm) X screws.
X
24
RO
6
STEP 6
1. Fasten the B Minifix screws to the parts 4 & 8.
B
8
8
4
STEP 7
1. Fit the part 4 on the parts 2.
2. Fit the part 7 on the part 4.
3. Fit the C Minifix Barrels in the parts 2 & 7, and then turn to
block with a Phillips screwdriver.
C
5
R
5
4
7
9
2
A
4
2
STEP 8
1. Fit part 8 on the parts 5, 6 and 7.
2. Fit the C Minifix Barrels in the parts 5, 6 & 7, and then turn to
block with a Phillips screwdriver
C
3
5
3
R
7
5
STEP 9
1. Join the parts 12 & 13 with the EE junction and the (4x12mm)
X screws.
EE
1
X
2
1
1. Fasten the angle support to the parts 12 & 13 with the
STEP 10
(4x12mm) X screws.
X
5
H
5
1. Fasten the T angle to the part 11 with the (4x12mm) X screws.
STEP 11
X
6
T
3
STEP 12
1. Fasten the set assembled at the previous step to the parts 2 &
4 through the H supports with the (4x12mm) X screws.
X
5
STEP 13
1. Fasten the set assembled at the previous step to the parts
4 & 12 through the T angles and the (4x12mm) X screws.
X
6
6
STEP 14
D
35
12
13
E
5
STEP 15
13
X
4
12
M
2
STEP 16
S
1
11
STEP 17
2
M
12
4
13
M
2
STEP 18
4
12
11
1. CAUTION: Before fastening the bottoms check the cabinet
square.
2. Align the parts 15, 16 & 17, and then fasten them with the D
nails.
3. Use the E fasteners and the D nails on the back junction
between the parts (15 & 16) and (16 & 17).
17
16
15
1. Fit the M hinges in the door 14, and then fasten them with
the (4x12mm) X screws.
14
1. Align the S Handles with the holes of the door 14, and then
fasten them with the (4x12mm) X screws.
14
1. To mount the door, fit the M Hinges in the M wedges blocking
it to the screw indicated with nr. 1 below.
6
1
14
To adjust the doors, follow these instructions.
1. If you need to raise or lower the door a little, loosen slightly the
screws indicated with the number 1, replace it and fasten again.
2. If you need to push the door into or pull it out, loosen slightly
the screws indicated with the number 2, replace it and fasten
again.
3. If you need to align the doors a little farther to the center or to
the sides, use a Phillips screwdriver to turn the screw
indicated with the nr. 3 until you get it set to
the right place.
3
1
2
Publicidad
