Taurus RAPIDISSIMO CLEAN PRO II Manual Del Usuario página 13

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
- Check that the surface to be cleaned can resist steam cleaning.
- Do not move the steamer by pulling on the cable or the hose. Use the
corresponding handle.
- Do not add aromas, alcohol or detergents inside the steamer as this may
damage it.
- Never touch the hot surfaces whilst using the steamer. Let the accessories
cool down before replacing them.
- WARNING: Danger of burning on hot surfaces.
- Any inappropriate use or the non- observance of the instructions for use,
renders the guarantee and the manufacturer's liability null and void.
Instructions for Use
Filling up the boiler before using the steamer.
- Never leave the appliance connected to the mains.
- Unscrew Safety Stopper F by pressing down and turning slightly in an anti-
clockwise direction (Fig. 3).
- Pour in water using the measuring cup and funnel supplied. The steamer's
maximum capacity is 1.7 lt.
- Unscrew Safety Stopper F by pressing down and turning slightly in an anti-
clockwise direction to the
end.
Using the steamer.
- Plug the appliance into the mains.
- Turn it on by pressing on the main on/off switch B (Fig. 4). This will switch on
red pilot light C (Fig. 4).
- Put steam gun L in place, attaching it to the base using steam plug K (Fig. 5).
- Wait for green steam ready light D to come on (Fig. 4). At that moment,
Instructions for Use Filling up the boiler before using the steamer.
- Never leave the appliance connected to the mains.
- Unscrew Safety Stopper F by pressing down and turning slightly in an anti-
clockwise direction (Fig. 3).
- Pour in water using the measuring cup and funnel supplied. The steamer's
maximum capacity is 1.7 lt.
- Unscrew Safety Stopper F by pressing down and turning slightly in an anti-
clockwise direction to the
end.
Using the steamer.
- Plug the appliance into the mains.
- Turn it on by pressing on the main on/off switch B (Fig. 4). This will switch on
red pilot light C (Fig. 4).
- Put steam gun L in place, attaching it to the base using steam plug K (Fig. 5).
- Wait for green steam ready light D to come on (Fig. 4). At that moment,
the steamer is ready to be put into operation.
- Place the desired accessory, following the instructions set forth in the section
Accessory attachment and use.
- Press steam release button N, making sure that steam release button O not
jammed(Fig. 2).
- NOTE: When pressing steam release button N for the first time or after a cer-
tain amount of time out of use, a few drops of water may form due to the initial
heat instability. This is normal and is simply caused by steam condensating
in the conducts. If this occurs, it is advisable to release the steam into a cloth,
keeping steam release button N pressed and then
wait a few seconds until the droplets disappear.
- By turning steam flow regulator E in an anti-clockwise direction, the steam flow
released increases. To decrease, turn it in the opposite direction (Fig. 4).
Filling up the boiler during use.
- Switch off the appliance by pressing the general on/off button B, ensuring that
the red pilot light has gone off
and then unplug the power supply cable from the mains.
- Eliminate the steam pressure, pressing steam release button N.
- Slowly unscrew the safety stopper F to enable the remaining steam that might
be in the water tank to be released slowly.
- Wait a few moments and then slowly pour in 1,7L, with the aid of the measu-
ring cup and the corresponding funnel.
- Unscrew Safety Stopper F by pressing down and turning slightly in an anti-
clockwise direction to the end.
Access to built-in accessories.
The steamer is fitted with a series of built-in accessories in the accessory holder
compartment (Fig. 1). To access these, press lightly on flaps H (fig 6), pulling
lightly upwards on
the carrier handle.
Fitting and using the accessories. Extension Tubes Q
- Line up the main steam nozzle M with extension tube Q on the end fitted with
the corresponding attachment.
- Press extension tube Q against the main steam nozzle M until you hear a
click (Fig. 7).
- Repeat this procedure if it is necessary to attach more tubes, using the
Buttons to attach/detach
extension tubes R.
- Use extension tubes Q to increase the distance from steam gun L to the
chosen accessory (floor cleaner,...).
Manual Rapidissimo Clean Pro.indb 13
U Pad
Initial pre-assembly with the T connector pad (Fig. 8).
- Line up the round end of connector pad T with the side hold on the U pad so
that the T pad connector tube is pointed downwards.
- Press until these items click into place.
- Twist the T pad 180 º from the U pad. The set is now assembled and ready to
be attached to other parts.
Connection with extension tube Q
- Line up extension tube Q with the circular nozzle end of the T pad connector,
at the corresponding end.
- Press extension tube Q against the T pad connector until you hear a click
(Fig. 9).
- Use pad U to clean floors and washable walls. The U pad can be used with or
without the W cloth pad.
Attaching W pad cloth (Fig 10).
- Place pad cloth W out on a horizontal surface.
- Centre Pad U on Pad cloth W.
- Use the pad cloth V attachment flaps, located on either side of the U pads to
firmly attach pad cloth W to pad cloth U.
- Use Pad U with Pad cloth W to clean delicate surfaces (wood, parquet), and to
dry the surface being cleaned when using the steamer.
Accessory adaptor X.
- Line up the main steam nozzle M with accessory adaptor X on the end fitted
with the corresponding attachment.
- Press accessory adaptor X against the main steam nozzle M until you hear
a click (Fig. 11).
- Use accessory adaptor X to attach various different accessories (concentrator
nozzle, 45 nozzles, round brushes, fabric brushes), depending on the task to
be performed.
Concentrator nozzle Y (Fig. 12).
- Line up the circular end of extension tube Q or accessory adaptor X with
the side hole in concentrator nozzle Y, according to the existing marks in
concentrator nozzle Y.
- Press until these items click into place.
- Turn concentrator nozzle Y 90 º anti- clockwise as marked. The set is now
assembled and ready to be attached.
45 º Z Nozzle and AA Round Brushes
- Directly attach by pressure to concentrator nozzle Y or using accessory
adaptor X (Fig. 13).
- Use in combination with concentrator nozzle Y or with accessory adaptor X for
cleaning hard to access areas (corners, joins, radiators, shutters,...).
- The wire brush is specifically intended for use on floors and rough surfaces
and should not be used for cleaning delicate surfaces (sofas, chairs,...).
- The round plastic brush is specifically intended for use on delicate surfaces,
and is not recommended for use on floors or rough surfaces.
- Use round brushes AA with cloth brush AB to dry the surface being cleaned.
AC brush for textiles (Fig. 14).
- Directly attach by pressure to concentrator nozzle Y, making sure the marks
are lined up.
- This accessory is specifically intended for cleaning curtains, cushions, rugs, ...
Window cleaner accessory AD (Fig 15).
- Place the notches on the inside of this accessory and the fabric brush AC.
- Rotate the top of the window cleaning accessory AD and press into the fabric
brush AC until you hear a click.
- This accessory is specifically intended for windows, mirrors, tiles and ceramic
surfaces.
- For cleaning glass (Fig 16):
- Spray steam uniformly at a distance of 20 cm.
- WARNING: Glass surfaces can crack if exposed to excessive heat. Therefore,
apply the steam to the glass surface at a distance of 20-25 cm. The distance
can then be reduced to 15 cm.
- Disconnect the steam and clean the glass condensation from bottom to top
with the aid of a rubber band.
- Clean the rubber band and dry the bottom frame of the window after each one.
Storage.
- Place the built- in accessories in the corresponding compartment (see Access
to Built- in Accessories). The rest of the accessories can be kept beside the
appliance.
- The steamer has two storage/parking positions: horizontal and vertical (Fig.
17).
Cleaning
It is advisable to clean the deposit after each 5 fills. To do so, proceed as
follows:
- Unplug the steamer, release the pressure and let it cool down fully.
- Fill up the deposit using the measuring cup and the funnel with tap water,
shake it up vigorously and empty it out.
Repeat the operation two or three times successively.
30/01/14 12:06

Publicidad

Tabla de contenido
loading

Tabla de contenido