Technical Data - Felisatti MF800VE Instrucciones De Servicio

TECHNICAL DATA

Mixer
Rated power
No load speed
Work shaft thread
Torque
Approx. weight
The instructions contained in this manual must be strictly
followed, it should be carefully read and kept close at
hand to use when carrying out maintenance on the
indicated parts.
If the machine is used carefully and normal maintenance
is carried out, it will work well for a long time.
The functions and use of the tool you have bought shall
be only those described in this manual. Any other use
of the tool is strictly forbidden.
ILLUSTRATIONS
DESCRIPTION (See figures)
A Safety push button switch (Fig.1)
B On-/off switch (Fig.1)
C Drill chuck shaft gap (Fig.1)
D Mechanical speed shift lever (Fig.3) (Except
MF800VE)
E Auxiliary grip (Fig.1)
F Speed adjustment (Fig.1)
EQUIPMENT
- M14 adapter
- Mixing rod
- Operating instructions
- Safety instructions
- Warranty
SAFETY INSTRUCTIONS
 See "Safety Instructions" manual, supplied with this
instruction manual.
 Warning! Follow the insurance company's safety
instructions regarding the responsibility of employees.
 For your personal safety, always connect the machine
to a mains supply protected by a differential and ther-
mal cut-out switch, in accordance with regulations on
low-voltage wiring sitemaps.
 Do not perforate the machine casing, as this would
destroy the protective insulation (use adhesive labels).
 Always unplug the machine before doing any work on it.
 Warning! Before each use, inspect the plug and lead.
Should they need replacing, have this done by an offi-
cial service centre. Only plug the machine in when it is
switched off.
 Always keep the lead out of the machine's working area.
 Only plug the machine in when it is switched off.
 Do not allow the machine to get wet, nor should it be
used in wet environments.
 When using the machine, always wear safety goggles,
gloves and non-slip footwear, and it is advisable to
wear ear protection.
 Hold the machine firmly by the handle and the auxiliary
handle, otherwise the recoil produced could cause the
machine to work imprecisely or even dangerously.
W
rpm
ISO
Nm
kg
MF800VE
800
150-570
5/8"x16
42
2.4
 The machine must not be used at a location where a
danger of explosion exists.
 Solvents or products containing solvents must not be
mixed since there is a danger of igniting if the tempera-
ture exceeds 21ºC.
 Officially approved extension cables must be used for
outside operations.
 The machine should only be start and stopped inside a
container and this must be firmly fixed in place and
unable to move.
 Hands or other objects should not be inserted into the
container when working with the machine in operation.
 The machine should be inserted into or removed from
the container at a low speed, and once inside, speed
can be increased to maximum in order to prevent ma-
chine over-heating and it should be moved in all direc-
tions to guarantee thorough mixing.
BRIEF DESCRIPTION
The mixer is used to mix liquid products, such as
mortar, adhesive paste, paints epoxy resins, cement
and similar products.
Optimum mixer performance depends on the density of
the product to be employed and amount to be mixed, the
correct mechanism must be used for each situation.
BEFORE USING THIS TOOL
Make sure the mains voltage is correct: it must be the
same as that on the specification label. Machines with
230V can also be connected to a 220-V mains supply.
START UP
WARNING! Only plug in when machine is switched off.
Press the locking button A, and squeeze the trigger in
the on/off switch B. When the on/off switch is released,
the machine stops.
For safety reasons, it is not possible to lock On/Off
switch B, instead it has to be pressed while the machine
is being used.
Installing the mixer rod.
Screw the adapter (5/8" thread) onto the machine shaft
using one fixed spanner on the faces of chuck C and
another spanner on the adapter and tighten, screw M14
thread mixer rod into the adapter, use a fixed spanner
on the adapter and another on the rod hexagon and
tighten it, to remove the rod or change it, these instruc-
tions should be followed in reverse order.
Mains connection
Warning! Connect only to a single-phase AC current
supply and only to the mains voltage specified on the
rating plate. Connection to sockets without earth protec-
tion is possible as the appliance features protective
class II insulation according to European Standard EN
MF1200/VE2
1200
120-405/245-825
5/8"x16
53/27
4.6