Publicidad
Enlaces rápidos
Parts List • Liste des Pièces • Lista de Partes
1.
Main Worksurface
Table
Mesa
2.
Bottom Shelf
Étagère Inférieure
Estante Inferior
3.
Top Shelf
Étagère Supérieure
Estante Superior
4.
Vertical Panel - Left Side
Panneau Verticale Gauche
Panel Vertical Izquierdo
5.
Vertical Panel - Center
Panneau Verticale Du Centre
Panel Vertical De Centro
6.
Vertical Panel - Right Side
Panneau Verticale Droite
Panel Vertical Derecho
7.
Rear Leg - 2 Holes For Rear Panel
Jambe Arrière - 2 Trous pou Panneau Arrière
Pata Trasera - 2 Agujeros para Panel Trasero
8.
Front Leg
Jambe Avant
Pata Delantera
9.
Rear Panel
Panneau Arrière
Panel Trasero
10. Bracket
Plaque
Placa
1
1
1
1
1
1
2
2
1
4
Creation Station 409556
Publicidad
Resumen de contenidos para Thoman StudioRTA Creation Station 409556
- Página 1 Parts List • Liste des Pièces • Lista de Partes Main Worksurface Table Mesa Bottom Shelf Étagère Inférieure Estante Inferior Top Shelf Étagère Supérieure Estante Superior Vertical Panel - Left Side Panneau Verticale Gauche Panel Vertical Izquierdo Vertical Panel - Center Panneau Verticale Du Centre Panel Vertical De Centro Vertical Panel - Right Side...
- Página 2 Parts List • Liste des Pièces • Lista de Partes 11. Caster - Locking Roullette Avec Freine Rueda Con Seguro 12. Caster - Non-Locking Roullette Sans Freine Rueda Sin Seguro 13. Cam Bolt Boulon De Came Perno De Leva 14. Cam Lock Serrure De Came Cerradura De Leva 15.
- Página 3 Warning: Do not tighten Bolts and Screws until Step 4. 1. Lay Main Worksurface (1) on a clean, flat surface with holes facing up. 2. Attach Rear Legs (7) (holes face rear - see arrows) using Phillips Screws (18). 3. Attach Front Legs (8) using Phillips Screws (18). 4.
- Página 4 1. Place Bottom Shelf (2) (holes facing up) onto Legs and attach using Allen Bolts (16). 2. Attach Locking and Non-Locking Casters (11 and 12) using Phillips Screws (18). 1. Placez L’étagère Inférieure (2) (trous vers le haut) sur Jambes et attachez à l'aide des Boulons Allen (16). 2.
- Página 5 1. Carefully turn unit right side up. 2. Attach Brackets (10) to Vertical Panels (4, 5 and 6) using Phillips Screws (18). 3. Place Vertical Panels (4, 5 and 6) on Main Worksurface and attach using Allen Screws (15). 1. Soigneusement tournez l'unité autour. 2.
- Página 6 1. Screw Cam Bolts (13) into Top Shelf (3). 2. Insert other end of Cam Bolts into holes in Vertical Panels. 3. Insert Cam Locks (14) into holes in Vertical Panels (arrow towards Cam Bolt) and turn clockwise until secure (do not overtighten). 4.
- Página 7 35 Lbs. / 15,87 kg. 50 Lbs. / 22,68 kg. 50 Lbs. / 22,68 kg. Please use care and good judgement when placing objects on top and shelves. DO NOT exceed the weight limits shown. Précaution est de rigueur lorsque vous placez objets sur la table et l’étagères. NE DEPASSEZ pas les limites montrées.