Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
ASSEMBLY INSTRUCTIONS
ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE
PARTS LIST
PART
MATERIAL CODE
NO.
1
KTS794T-CS11-1
2
KTS794T-CS04-1
3
17C40A0712001YX
4
17C40A0716001YX
Attention:
Make sure that each bolt needed for all steps matches
the corresponding figure to ensure proper assembly.
Step 1:
Fasten the seat assembly (#1) to the base assembly
(#2) by using bolts (#3). Keep the bolts loose.
See Figure 1.
!
Use the correct bolts as indicated. Do not tighten any of the bolts until the chair is completely
assembled.
!
Do not discard of any of the packaging until you have checked that you have all of the parts and
fittings required.
!
Keep children away during assembly. This item contains small parts that can be swallowed by
children. Children should always be under direct adult supervision while using this product.
!
Retain these assembly instructions for future reference.
!
Quote the following FQC NO.when contacting the service center.
V-4
INTENDED FOR RESIDENTIAL USE ONLY.
KTS794T
PART
Q'TY
1
SEAT ASSEMBLY
1
BASE ASSEMBLY
2
BOLT M6*35
2
BOLT M6*45
SERVICE CENTER TOLL FREE NO.
TEL: 1-877-539-7436
FAX: 1-877-539-7439
DO NOT RETURN TO THE STORE!
STOP
PAGE 1 OF 2
PART
MATERIAL CODE
NO.
5
1808010345701
6
17KAA0101----Y4
7
61K794TX00001BA
8
61K794TY00001BA
FIGURE 1
2
#3 BOLT M6*35
COURTYARD CREATIONS INC.
PART
PLASTIC CAP
HEX.KEY WRENCH 4MM
BACK CUSHION
SEAT CUSHION
1
3
35
Q'TY
2
1
1
1
5
Publicidad
Manuales relacionados para Rich Context KTS794T
Resumen de contenidos para Rich Context KTS794T
- Página 1 ASSEMBLY INSTRUCTIONS ATTENTION: THIS PRODUCT IS NOT FOR COMMERCIAL USE INTENDED FOR RESIDENTIAL USE ONLY. KTS794T PARTS LIST PART PART MATERIAL CODE PART Q’TY MATERIAL CODE PART Q’TY KTS794T-CS11-1 1808010345701 SEAT ASSEMBLY PLASTIC CAP KTS794T-CS04-1 17KAA0101----Y4 BASE ASSEMBLY HEX.KEY WRENCH 4MM...
- Página 2 FIGURE 2 FIGURE 3 #4 BOLT M6*45 Step 2: Step 3: Fasten the seat assembly (#1) to the base assembly Place the cushions (#7 and #8) onto the chair. Secure (#2) by using bolts (#4). Make sure that all of the bolts the cushions to the chair by using the velcro straps.
- Página 3 INSTRUCCIONES PARA EL MONTAJE ATENCIÓN: ESTE PRODUCTO NO SE UTILIZA PARA FINES COMERCIALES, SOLO PARA USO RESIDENCIAL. KTS794T LISTAS DE PARTES NO.DE CANT NO.DE CANT CÓDIGO DEL CÓDIGO DEL PARTE PARTE PARTE. IDAD PARTE. IDAD MATERIAL MATERIAL KTS794T-CS11-1 1808010345701 ASIENTO DEL...
- Página 4 FIGURA 2 FIGURA 3 TORNILLO M6*45 Paso 2: Paso 3: Sujete el asiento del montaje (#1) a la base del Poner los cojines (#7 y #8) sobre la silla. Fije los cojines montaje (#2) mediante tornillos (#4). Asegúrese de a la silla utilizando las tiras de velcro. Ver Figura 3. que todos los tornillos han sido completamente ajustado y tapas de plástico (#5).