Sony MDR-EX56LP Manual De Instrucciones

Stereo Headphones
Operating Instructions
Manual de instrucciones
MDR-EX56LP
©2009 Sony Corporation Printed in Thailand
A
B
1
Sectional View
2
C
English
Features
• Earbud-style headphones deliver detailed and rich sound reproduction with deep bass
• Silicone earbud housing for comfortable and soft fit in the ear
• Robust sound achieved by use of high-power neodymium magnets
4-131-510-11(1)
Colored parts
3
How to use
-
Wear the earpiece marked R in your right ear and the one marked L in your left ear.
How to use the supplied cord adjuster (see fig. A)
You can adjust the cord length by winding the cord on the cord adjuster.
(The cord can be wound to the cord adjuster up to 50 cm. If you wind more, the cord
comes off from the cord adjuster easily.)
1
Wind the cord.
2
Push cord into slot hole to secure in place.
Note
Do not wind the plug or split section of the cord, as it will strain the cord and may cause
a wire break.
How to install the earbuds correctly (see fig. B)
If the earbuds do not fit your ears correctly, low-bass sound may not be heard. To enjoy
better sound quality, change the earbuds to another size, or adjust the earbuds position to
sit on your ears comfortably and fit your ears snugly.
If the earbuds do not fit your ears, try another size. Confirm the size of the earbuds by
checking color inside (see fig. B–1).
When you change the earbuds, turn to install them firmly on the headphones to prevent
the earbud from detaching and remaining in your ear.
Earbud sizes (inside color)
Small
>
SS* S M
(Red) (Orange) (Green)
* This size is optional and available at purchase.
To detach an earbud (see fig. B–2)
While holding the headphone, twist and pull the earbud off.
z Tip
If the earbud slips and cannot be detached, wrap it in a dry soft cloth.
To attach an earbud (see fig. B–3)
Push the parts inside of the earbud into the headphone until the projecting part of the
headphone is fully covered.
Cleaning the earbuds
Remove the earbuds from the headphones, and wash them with a mild detergent solution.
Specifications
Type: Closed, dynamic / Driver units: 9 mm (CCAW adopted), dome type / Power
handling capacity: 100 mW (IEC*) / Impedance: 16 Ω at 1 kHz / Sensitivity:
100 dB/mW / Frequency response: 6 – 23,000 Hz / Cord: 1.2 m (47
cord / Plug: Gold-plated L-shaped stereo mini plug / Mass: Approx. 3 g (0.11 oz.)
without cord
Supplied accessories
Earbuds (S × 2, M × 2, L × 2), Cord adjuster (1), Carrying pouch (1)
*IEC = International Electrotechnical Commission
Design and specifications are subject to change without notice.
Precautions
• Please keep your headphones clean at all times especially inside the rubber earbud
(see fig. C).
If any dust or ear wax inside the earbud, you may experience some listening
difficulties.
• Listening with headphones at high volume may affect your hearing. For traffic safety,
do not use while driving or cycling.
• The earbuds may deteriorate due to long-term storage or use.
• Install the earbuds firmly onto the headphones. If an earbud accidentally detaches and
is left in your ear, it may cause injury.
Note on static electricity
In particularly dry air conditions, mild tingling may be felt on your ears. This is a result
of static electricity accumulated in the body, and not a malfunction of the headphones.
The effect can be minimized by wearing clothes made from natural materials.
EP-EX10A is available (sold separately) as optional replacement earbuds.
EP-EX10A offers 4 types of the earbuds: SS, S, M and L.
Large
.
L
(Light blue)
1 /
4
in), OFC litz