Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

WARNING
Study, understand and follow all instructions provided
with this product. Read these instructions carefully
before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe, accessible place.
INTENDED USE OF THE TOOL
The SKR Cordless Soldering Iron is designed to solder
electrical connections and apply heat shrink insulation.
TOOL QUICKLY BECOMES EXTREMELY HOT, WEAR
ANSI GLOVES AND EYE PROTECTION. Do not use this
tool outside of the designed intent. Never modify the
tool for any other purpose or use.
WARNING
Caution: To help prevent personal injury
• Use of this product can expose you to chemicals
including ethylene glycol, gasoline vapors and engine
exhaust, which are known to the State of California to
cause cancer, birth defects, or reproductive harm. For
more information, visit www.P65Warnings.ca.gov.
Always wear ANSI approved safety equipment, safety
glasses and clothing when using this product. Study,
understand, and follow all instructions provided with
this product. Failure to read and follow all warnings
and operating instructions may result in damages and
serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct
size and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is
in a secure position, and will not move during repair.
BEFORE USE
When unpacking, check the parts diagram and part
number listing on page 7 to make sure all parts are
included. If any parts are missing or damaged, please
call your distributor.
CORDLESS RECHARGEABLE
SOLDERING IRON
The manufacturer warrants this product to the original
user against defective material or workmanship for a
period of 1 year (#01 Soldering body only, accessories
are consumable) from the date of purchase.
The manufacturer reserves the right to determine
whether the part or parts failed because of defective
material, workmanship or other causes. Failures caused
by accident, alteration, or misuse are not covered by
this warranty.
The manufacturer, at its discretion, will repair or replace
product covered under this warranty, free of charge.
Repairs or replacements of products covered under this
warranty are warranted for the remainder of the original
warranty period.
The manufacturer or its authorized service representatives
must perform all warranty repairs. Any repair to the
product by unauthorized service representatives voids
this warranty. The rights under this warranty are limited
to the original user and may not be transferred to
subsequent owners.
The warranty is in lieu of all other warranties, expressed
or implied, including warranties of merchantability and
fitness for a particular purpose. Some states do not allow
the exclusion or limitations of incidental or consequential
damages, so the above limitations may not apply to you.
PRODUCT INFORMATION:
Rapid start. Industry leading 8 seconds from cold to
soldering temperature with the press of a button,
up to 1,100°F.
Mobile. No cords or butane exhaust to worry about and
three quickly interchangeable heads including point tip,
chisel tip and heat shrink coil.
Works longer. Twice the run time as the competition,
40 minutes of continuous soldering with LED work light.
SPECIFICATIONS
Internal battery:
Charging source:
Charging time:
Running time:
Max Temperature:
Page 1
MIXED WARRANTY
Li-lon 2,400mAh
USB port 5V
3-4 hours
Soldering Iron: 40 minutes
600°C (1112°F)
DO NOT DISCARD – GIVE TO USER
SKR
Made in Taiwan
to Matco specifications
2003049-14

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Matco Tools SKR

  • Página 1 Keep these instructions in a safe, accessible place. INTENDED USE OF THE TOOL Made in Taiwan The SKR Cordless Soldering Iron is designed to solder to Matco specifications electrical connections and apply heat shrink insulation. MIXED WARRANTY...
  • Página 2 CORDLESS RECHARGEABLE SOLDERING IRON CHARGING INSTRUCTIONS This tool is rechargeable. Using the supplied cable, insert the Micro USB connector into the end of the tool and the USB connector to a wall charger/computer port. A full charge will take approximately 3.5 hours. Once charged, the indicator light will turn green. SOLDERING INSTRUCTIONS 1.
  • Página 3 Made in Taiwán EL USO DE LA HERRAMIETA to Matco specifications El soldador inalámbrico SKR está diseñado para soldar (M) GARANTÍA MIXTA conexiones eléctricas y aplicar aislamiento El fabricante garantiza este producto al usuario original termocontraíble.
  • Página 4: Instrucciones De Carga

    HIERRO PARA SOLDAR RECARGABLE E INALÁMBRICO INSTRUCCIONES DE CARGA Esta herramienta es recargable. Usando el cable suministrado, inserte el conector Micro USB en el extremo de la herramienta y el conector USB a un cargador de pared y/o puerto de computadora. Una carga completa tomará...
  • Página 5: Informations Produit

    Fabriqué à Taïwan UTILISATION PRÉVUE DE L’OUTIL les spécifications de Matco Le fer à souder sans fil SKR est conçu pour souder les (M) GARANTIE MIXTE connexions électriques et appliquer une isolation Le fabricant garantit ce produit à l'utilisateur d'origine thermorétractable.
  • Página 6: Instructions De Charge

    FER À SOUDER RECHARGEABLE SANS FIL INSTRUCTIONS DE CHARGE Cet outil est rechargeable. À l'aide du câble fourni, insérez le connecteur Micro USB dans l'extrémité de l'outil et le connecteur USB à un chargeur mural / port d'ordinateur. Une charge complète prendra environ 3,5 heures. Une fois chargé, le voyant passe au vert. INSTRUCTIONS DE SOUDURE 1.
  • Página 7: Parts Breakdown

    CORDLESS RECHARGEABLE SOLDERING IRON PARTS BREAKDOWN Parts List Index Part No. Description SKR-01 Solder/Staple Body F/SKR/HSGKR SKR-02 Point Soldering Tip SKR-03 Chisel Soldering Tip SKR-04 SKR-05 Charging Cord F/SKR/HSGKR SKR-06 Heat Shrink Tip SK8MAT07 Sponge With Tray SK8MAT08 Solder ON/OFF Switch...
  • Página 8: Desglose De Piezas

    RECARGABLE E INALÁMBRICO DESGLOSE DE PIEZAS Lista de Piezas Número Número Descripción Cantidad de pieza de índice SKR-01 Soldadura/Cuerpo de Grapas F/SKR/HSGKR SKR-02 Punta de Soldadura de Puntos SKR-03 Punta de Soldadura de Cincel SKR-04 Gorra SKR-05 Cable de Carga F/SKR/HSGKR SKR-06 Punta Termica Para Encoger (Termorretráctil)
  • Página 9: Liste De Pièces

    RECHARGEABLE SANS FIL VENTILATION DES PIÈCES Liste de Pièces Numéro Numéro La description Quantité d'article d'index SKR-01 Corps de Soudure/d'agrafage F/SKR/HSGKR SKR-02 Pointe à Souder par Point SKR-03 Pointe à Souder au Burin SKR-04 Casquette SKR-05 Cordon de Charge F/SKR/HSGKR SKR-06 Pointe Thermorétractable...

Tabla de contenido