Keeney SCH 40 Instrucciones De Instalación

Installation Instructions for SCH 40 Full Soak Foot Lok Stop Bath Drain
You are required to thoroughly read all instructions. This Instruction sheet must be provided to the end user. Do not overtighten during installation or maintenance.
FAILURE TO COMPLY WITH PROPER INSTALLATION, USE AND MAINTENANCE INSTRUCTIONS COULD RESULT IN PRODUCT FAILURE, WATER DAMAGE,
AND INJURY. DO NOT EXPOSE TO CORROSIVE MATERIALS.
Components included with kit:
A - Full Soak Stopper (1)
B - Face Plate Housing (1)
C - Face Plate Housing Washer (1)
D - Beveled Overflow Washer (1)
E - Overflow Elbow (1)
F - Face Plate Housing Screws (2)
G - 1-1/2" x 11 7/8" Overflow Tube (1)
H - Drain Stopper (1)
I - Drain Assembly (1)
J - Strainer Washer (1)
K - Waste Shoe (1)
L - Waste Tube (1)
M - Tee (1)
Tools needed (not shown):
- Solvent weld primer and cement
- Plumber's putty
- Tub drain wrench
- Wrench
- Screwdriver
Installation Instructions:
1. Measure, cut and dry fit waste shoe (K), tee (M), overflow elbow (E), and tubes (L & G) per diagram. Cut tube (L & G) so that the overflow opening and drain
waste shoe opening line up with the tub cutouts. Once the proper length is achieved connect all parts using solvent weld primer and cement. (Diagram 1)
2. Apply plumbers putty to the underside of the drain assembly (I) and place into the drain cutout of the tub.
3. Place strainer washer (J) between waste shoe (K) and tub and thread drain assembly (I) into waste shoe (I) and tighten using a tub drain wrench. Remove
any excess plumber's putty that squeezes out. (Diagram 2)
4. Thread drain stopper (H) into drain assembly (I). (Diagram 3)
5. Place beveled overflow washer (D) between tub and overflow elbow (E) Note: Beveled overflow washer (D) can be oriented thick side up or down depending
on tub angle. (Diagram 4)
6. Peel the adhesive guard off of Full Soak faceplate washer(C). Firmly stick to back of face plate housing. Align Full Soak face plate housing (B) with
threaded holes in overflow, insert face plate screws (F) and tighten. (Diagram 4)
7. Thread Full Soak stopper (A) into faceplate housing until it creates a water tight seal when depressed.
8. Complete connection to existing drainage and run water to test for leaks.
How to use:
For Foot Lok Drain Stop:
- To fill tub press drain stopper down
- To empty tub press drain stopper down
For Fullsoak Overflow Stopper:
- To fill tub past overflow drain, push Fullsoak stopper in
- Press Fullsoak stopper in again and release to restore overflow drain
function
Maintenance:
- Wipe dry after each use with a soft dry cloth to prevent water-spotting
and mineral build-up.
- Clean with mild soap and water
- Avoid all abrasive and aggressive chemicals
- Avoid ammoniated products (window cleaner, tile cleaners, etc.).
- Avoid bleach. Do not use abrasive cleaning pads.
Keeney Holdings LLC, Cleveland, OH 44135
A B C D
F
G
H
I
J
K L M
1-800-243-0526
E
K
(1)
A
(4)
Troubleshooting:
Problem: Water drains slowly or not at all when in open position
Solution:
1. Remove strainer and clear any obstruction.
2. Clean with drain cleaner or drain snake to remove clogs.
Problem: Tub will not hold water when in closed position.
Solution:
1. Ensure drain stopper is threaded all the way down.
2. Drain stopper may need replacing.
3. Check for leaks at joints and seals.
!
The Full Soak overflow stopper, when placed in
Warning:
the closed position, eliminates the overflow drain. Accordingly,
supervision is required when tub is being filled with the fullsoak
stopper closed. Do not fill bathtub past overflow housing before
getting in. Failure to do so can result in water damage and/or injury.
E
I
J
K
(2)
G
M
L
(3)
B C
F
Instructions for Schedule
40 Full Soak Foot Lok Stop
I630PVCFS
H
D E
©2020